View LTL1CHJETNN-002_9033968.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL1CHJETNN-002 spec no.: ds20-2003-211effective date: 08/30/2003revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * high luminous intensity output. * low power consumption. * high efficiency. * versatile mounting on p.c. board or panel. * i.c. compatible/low current requirement. * 3.1 mm diameter package. package dimensions part no. lens source col or ltl1chjetnn - 002 red transparent alingap red notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 1.0mm(.04") max. 4. lead spacing is measured w here the leads emerge from the package. 5. specifications are subject to change without notice. part no. : ltl1chjetnn - 002 page : 1 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 parameter maximum rating unit power dissipation 75 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 9 0 ma dc forward current 30 ma derating linear from 5 0 c 0. 4 ma/ c reverse voltage 5 v operating temperature range - 40 c to + 10 0 c storage temperature range - 55 c to + 100 c lead soldering temperature [1.6mm(.063") from body] 260 c for 5 seconds part no. : ltl1chjetnn - 002 page : 2 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at t a =25 parameter symbol min. typ. max. unit test condition luminous intensity i v 180 400 mcd i f = 20ma note 1 viewing angle 2 1/2 45 deg note 2 (fig.5) peak emission wavelength p 632 nm measurement @peak (fig.1) dominant waveleng th d 624 nm note 4 spectral line half - width ? 20 nm forward voltage v f 2.05 2.4 v i f = 20ma reverse current i r 100 a v r = 5v capacitance c 40 pf v f = 0 , f = 1mhz note: 1. luminous intensity is measured with a light s ensor and filter combination that approximates the cie eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag . 4. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. part no. : ltl1chjetnn - 002 page : 3 of 1 1 bns - od - c13 1/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : ltl1chjetnn - 002 page : 4 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * compatible with radial lead automatic i nsertion equipment. * most radial lead plastic lead lamps available packaged in tape and reel. * 2.54mm (0.1") straight lead spacing available. * reel packaging simplifies handling and testing. folding packaging is available by adding suffix a on optio n. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 17.5 0.688 18.5 0.728 feed hole to overall component height h2 22.4 0.882 24.0 0.945 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead loca tion p1 4.4 0.173 5.80 0.228 center of component location p2 5.05 0.198 7.65 0.301 total taped thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape width w1 14.5 0.571 15.5 0.610 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748 part no. : ltl1chjetnn - 002 page : 5 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y packing spec 2 reel per inner carton total 3000pcs per inner carton 6 inner cartons per outer carton total 18000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing part no. : ltl1chjetnn - 002 page : 6 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y bin code list for reference luminous intensity unit : mcd @20ma bin code min. max. hj 180 310 kl 31 0 52 0 mn 52 0 88 0 note: tolerance of each bin limit is 15% dominant wavelength unit : nm @20ma bin code min. max. h27 613.5 617.0 h28 617.0 621.0 h29 621 .0 625.0 h30 625.0 629.0 h31 629.0 633.0 note: tolerance of each bin limit is 1nm part no. : ltl1chjetnn - 002 page : 7 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).consult liteons sales in advance for information on applications in which exceptional reliability is required, particularly when the failu re or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c t emperature or 70% relative humidity. it is recommended that leds out of their original packaging are used within three months. for extended storage out of their original packaging, it is recommended that the l ed s be stored in a sealed container with approp riate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the l ed s if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical st ress. 5. soldering when soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 300c max. 3 sec. max. (one time only) pre - heat pre - heat time solder wave soldering time 100c max. 60 sec. ma x. 260c max. 10 sec. max. note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led part no. : ltl1chjetnn - 002 page : 8 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 6. driv e method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each le d as shown in circuit a below. circuit model a circuit model b (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those l ed s 7. esd (electrostatic discharge ) static electricity or power surge will damage the led. suggestions to prevent esd damage: ? use a conductive wrist band or anti - electrostatic glove when han dling these leds ? all devices, equipment , and machinery must be properly grounded ? work tables, storage rack s, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing esd - damaged leeds will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or no light up at low currents. to verify for esd damage, check for light up a nd v f of the suspect l ed s at low currents. the v f of good l ed s should be >2.0v@0.1ma for i ngan product and >1.4v@0.1ma for alingap product. part no. : ltl1chjetnn - 002 page : 9 of 1 1 bns - od - c131/a4 chip esd level machine mode l human body mode l in gan / sapphire 100 v 300 v alingap 200 v 500 v i ngan / sic 600 v 1000 v led led
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y suggested checking list : tra ining and certification 1. everyone working in a static - safe area is esd - certified? 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 1. static - safe workstation or work - areas have esd signs? 2. al l surfaces and objects at all static - safe workstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors ) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dsl? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia - 471 labels on item or packaging? 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 3. no static charge generators (e.g. plastics) inside shiel ding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? part no. : ltl1chjetnn - 002 page : 10 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 8 . reliability test classification test item test condition refer e nce standard endurance test operation life ta= under room temperature as per data sheet maximum rating * test time= 1000hrs ( - 24hrs,+72hrs) mil - std - 750d:1026 (1995) mil - std - 883d:1005 (1991) jis c 7021:b - 1 (1982) high temperature high humidity storage ta= 655 rh= 90 95% test time= 24 0hrs2hrs mil - std - 202f: 103b(1980) jis c 7021 : b - 11(1982) high temperature high humidity reverse bias ta= 655 rh= 90 95% vr=5v test time = 500hrs ( - 24hrs, +48hrs) jis c 7021 : b - 11(1982) high temperature storage ta= 1055 * tes t time= 1000hrs ( - 24hrs,+72hrs) mil - std - 883d:1008 (1991) jis c 7021:b - 10 (1982) low temperature storage ta= - 555 * test time=1000hrs ( - 24hrs,+72hrs) jis c 7021:b - 12 (1982) environmental test temperature cycling 105 25 - 55 25 30mins 5mins 30mins 5mins 10 cycles mil - std - 202f:107d (1980) mil - std - 750d:1051(1995) mil - std - 883d:1010 (1991) jis c 7021: a - 4(1982) thermal shock 105 5 - 55 5 10mins 10mins 1 0 cycles mil - std - 202f:107d(1980) mil - std - 750d:1051(19 95) mil - std - 883d:1011 (1991) solder resistance t .sol = 260 5 dwell time= 10 1secs mil - std - 202f:210a(1980) mil - std - 750d:2031(1995) jis c 7021: a - 1(1982) solder ability t . sol = 230 5 dwell time= 5 1secs mil - std - 202f:208d(1980) mil - std - 750d:2026(1995) mil - std - 883d:2003(1991) jis c 7021: a - 2(1982) 9. others the appearance and specifications of the product may be modified for improvement, without prior notice. part no. : ltl1chjetnn - 002 page : 1 1 of 1 1 bns - od - c131/a4

▲Up To Search▲

Price & Availability of LTL1CHJETNN-002

	To Download LTL1CHJETNN-002 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .