 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| spec no. tq3c-8eaf0-e1dey71-00 s p e c date september 9, 2016 t y p e : t c g 0 6 2 h v l q a v n n - g n 2 0 < 6.2 inch hvga transmissive color tft with led backlight and constant current circuit for led backlight> kyocera display corporation this specification is subject to change without notice. consult kyocera before ordering. original issue date designed by: engineering dept. confirmed by: qa dept. prepared checked approved checked approved september 9, 2016 c o n t e n t s 1. application 2. construction and outline 3. mechanical specifications 4. absolute maximum ratings 5. electrical characteristics 6. optical characteristics 7. interface signals 8. input timing characteristics 9. backlight characteristics 10. lot number identification 11. warranty 12. precautions for use 13. reliability test data 14. outline drawing 4 f q
spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page - w a r n i n g 1 . t h i s k y o c e r a l c d m o d u l e h a s b e e n s p e c i f i c a l l y d es i g n e d f o r u s e o n l y i n e l e c t r o n i c d e v i c e s a n d i n d u s t r i a l m a c h i n es i n t h e a r ea o f a u d i o c o n t r ol , o f f i c e a u t o m a t i o n , i n d u s t r i a l c o n t r ol , h o m e a p p l i a n c e s , e t c . t h e m o d u l e s h o u l d n ot b e u s e d i n a p p l i c a t i on s w h e r e t h e h i g h e s t l ev el o f s a f et y a n d r e l i a b i l i t y a r e r e q u i r ed a n d m o d u l e f a i l u r e o r m a l f u n c t i o n o f s u c h m o d u l e r e s u l t s i n p h y s i c a l h a r m o r l o s s o f l i f e, a s w e l l a s e n o r m o u s d a m a g e o r l o s s . s u c h f i el d s o f a p p l i c a t i o n s i n c l u d e , w i t h o u t l i m i t a t i o n , m e d i c a l , a e r o s p a c e, c o m m u n i c a t i o n s i n f r a s t r u c t u r e, a t om i c e n er g y c o n t r ol . k y o c e r a e x p r e s s l y d i s c l a i m s a n y a n d a l l l i a b i l i t y r e s u l t i n g i n a n y w a y t o t h e u s e o f t h e m o d u l e i n s u c h a p p l i c a t i o n s . 2 . c u s t o m e r a g r ee s t o i n d em n i f y , d e f en d a n d h ol d k y o c e r a h a r m l e s s f r o m a n d a g a i n s t a n y a n d a l l a c t i on s , c l a i m s , d a m a g e s , l i a b i l i t i e s , a w a r d s , c o s t s , a n d e x p e n s e s , i n c l u d i n g l eg a l e x p e n s e s , r e s u l t i n g f r om o r a r i s i n g o u t o f c u s t om e r ' s u s e, o r s a l e f o r u s e , o r k y o c e r a m o d u l es i n a p p l i c a t i on s . c a u t i o n 1 . k y o c e r a s h a l l h a v e t h e r i g h t , w h i c h c u s t o m e r h e r eb y a c k n o w l e d g es , t o i m m e d i a t el y s c r a p o r d e s t r o y t o ol i n g f o r k y o c e r a m o d u l e s f o r w h i c h n o p u r c h a s e o r d e r s h a v e b ee n r e c e i v e d f r o m t h e c u s t om e r i n a t w o - y e a r p e r i o d . spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page - revision record date designed by : engineering dept. confirmed by : qa dept. prepared checked approved checked approved rev. no. date page descriptions spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 1 m628090 1. application this document defines the specification of TCG062HVLQAVNN-GN20 (rohs compliant) 2. construction and outline lcd backlight system polarizer additional circuit : transmissive color dot matrix type tft : led : glare treatment : power supply (3.3v input) (with constant current circuit for led backlight) 3. mechanical specifications item specification unit outline dimensions 1) 173(w)70(h)6.7(d) mm active area 147.84(w)55.44(h) (15.8cm/6.2 inch(diagonal)) mm effective viewing area 149.8(w)57.4(h) mm dot format 640(b,g,r)(w)240(h) dot dot pitch 0.077(w)0.231(h) mm base color 2) normally black - mass 115 g 1) projection not included. please refer to outline for details. 2) due to the characteristics of the lcd material, the color varies with environmental temperature. spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 2 m628090 4. absolute maximum ratings 4-1. electrical absolute maximum ratings item symbol min. max. unit supply voltage for lcd drive v dd 0 4.0 v supply voltage for backlight v in b 0 6.0 v input signal voltage rxini+, rxini- 1) 2) v i1 -0.3 v dd v rxck in+, rxck in- 2) v i2 -0.3 v dd v sc v i3 -0.3 v dd v blen (backlight on-off) v i4 0 v in b v vbrt (brightness ad just voltage) v i5 0 v in b v 1) i=0,1,2 2) v dd must be supplied correctly with in the range described in 5-1. 4-2. environmental absolute maximum ratings item symbol min. max. unit operating temperature 1) t op -20 70 c storage temperature 2) t sto -30 80 c operating humidity 3) h op 10 4) %rh storage humidity 3) h sto 10 4) %rh vibration - 5) 5) - shock - 6) 6) - 1) operating temperature means a temperature which operation shall be guaranteed. since display performance is evaluated at 25c, another temperature range should be confirmed. 2) temp. = -30c 48h , temp. = 80c 168h store lcd at normal temperature/humidity. keep them free from vibration and shock. an lcd that is kept at a low or a high temperature for a long time can be defective due to other conditions, even if the low or high temperature satisfies the standard. (please refer to ?precautio ns for use? for details.) 3) non-condensing 4) te mp. Q 40c, 85%rh max. temp. 40c, absolute humidity shall be less than 85%rh at 40c. 5) frequency 10 55 hz acceleration value (0.3 9 m/s 2 ) vibration width 0.15mm interval 10-55-10 hz minutes 2 hours in each direction x, y, z (6 hours total) eiaj ed-2531 6) acceleration: 490 m/s 2 , pulse width: 11 ms 3 times in each dire ction: x, y, z eiaj ed-2531 spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 3 m628090 v p -v n =|v id |>v th =?high? v n v p v th v tl v p -v n =|v id | spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 5 m628090 6-3. definition of viewing angle 6-4. brightness measuring points 1) rating is defined on the average in the viewing area. (measured point 1 5) 2) measured 5 minutes after the led is powered on. (ambient temp. = 25c) -x +x -y +y = 0 lower upper -x +x -y =0 right left direction direction +y (dot) (dot) 1603 3203 4803 60 120 180 1 2 3 4 5 spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 6 m628090 7. interface signals 7-1. lcd no. symbol description note 1 gndb gnd for led backlight 2 gndb gnd for led backlight 3 gndb gnd for led backlight 4 vbrt brightness adjust voltage (0v[max]~2.8v[min]) 5 blen backlight on-off (h : on , l : off) 6 v in b power supply for led backlight 7 v in b power supply for led backlight 8 v in b power supply for led backlight 9 nc nc 10 nc nc 11 v dd +3.3v power supply 12 v dd +3.3v power supply 13 gnd gnd 14 gnd gnd 15 rxin0- lvds receiver signal ch0(-) lvds 16 rxin0+ lvds receiver signal ch0(+) lvds 17 gnd gnd 18 rxin1- lvds receiver signal ch1(-) lvds 19 rxin1+ lvds receiver signal ch1(+) lvds 20 gnd gnd 21 rxin2- lvds receiver signal ch2(-) lvds 22 rxin2+ lvds receiver signal ch2(+) lvds 23 gnd gnd 24 rxckin- lvds receiver signal ck(-) lvds 25 rxckin+ lvds receiver signal ck(+) lvds 26 gnd gnd 27 nc nc 28 nc nc 29 gnd gnd 30 sc scan direction control (gnd or open: normal, high: reverse) 1) lcd connector mdf76gw-30s-1h(55) (hirose) matching connector mdf76-30p-1c (hirose) lvds receiver bu90r104(rohm) matching lvds transmitter bu8254kvt(rohm) or compatible 1) scanning sc : gnd or open sc : high spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 7 m628090 8. input timing characteristics 8-1. timing characteristics item symbol min. typ. max. unit note clock (ck) frequency 1/tc 11.58 12.85 14.16 mhz enable signal (de) horizontal period th 766 816 866 tc 54.1 63.5 - s 1) horizontal display period thd 640 tc vertical period tv 250 262 320 th vertical display period tvd 240 th refresh rate fv 50 60 70 hz 2) 1) please set a clock frequency, a vertical dormant period, and the horizontal dormant period so that the horizontal period should not reach less th an min. value. 2) if the refresh rate reach less than min. value, the deterioration of the display quality, flicker etc., may occur.( fv=1/tv) 3) ck count of each horizontal scanning time shou ld be always the same.vertical invalid data period should be "n" "horizontal scanning time". (n: integer) frame period should be always the same. vertical timing diagram data dh1 dh2 dh3 dh238 dh239 dh240 dh1 enab tvd tv horizontal timing diagram ck spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 8 m628090 8-2. data 8-2-1. 6bit input de : data enable na : not applicable 8-3. input data signals and display position on the screen d1dh1 d2dh1 d3dh1 d640dh1 d1dh2 d2dh2 d3dh2 d1dh240 d2dh240 d3dh240 rxin1 rxin2 1 cycle r1 g2 b3 de b5 b4 b3 b2 g2 b2 de g1 b1 b0 g1 b1 r4 r5 r1 r0 g0 g5 g4 g3 g0 r0 r3 r2 rxin0 na na spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 9 m628090 9. backlight characteristics temp.=25 item symbol min. typ. max. unit note supply voltage v in b 3.0 - 5.5 v ta=-20 70 on-off (h) blen 0.8v in b - v in b v - on-off (l) 0.0 - 0.2v in b v - led forward current if 14 15 16 ma vbrt=0 1.4v 1) 2) 2.8 3.0 3.2 vbrt=2.8v supply current i in b - 350 450 ma v in b =3.3v, if=15ma - 220 290 v in b =5.0v, if=15ma operating life 3) 4) t - 40,000 - h if=15ma, ta=25 1) for each led. 2) a forward current below 5.0ma may reduce the brightness uniformity of the led backlight. this is because the amount of light from each led chip is different. therefore, please evaluate carefully before finalizing the input current. 3) when brightness decrease 50% of minimum brightness. the average life of a led will decrease when the lcd is operating at higher temperatures. 4) life time is estimated data. (condition : if=15ma, ta=25 in chamber). 5) when you start-up, please charge in sequence of v in b->blen, or vbrt. when you shut-down, please stop in sequence of blen and/or vbrt->v in b. 6) please do not connect the other than our backlight to this output connector on the pcb. 7) in case v dd and v in b are supplied by a single power source, v dd & v in b, and gnd & gndb are connected directly and separately from the output on the power source. if the common wire are used for v dd & v in b, and for gnd & gndb, and are split near the pcb, and connect to each lcd driving circuit and backlight driving circuit, a flicker migh t be occurred due to a ripple between the both circuit. spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 10 m628090 8) vbrt-if characteristics wrong output terminal power supply (customer side) v in b gndb v dd gnd lcd pcb right output terminal power supply (customer side) v in b gndb v dd gnd lcd pcb vbrt (v) if (ma) 2.8 1.4 15 3.0 spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 11 m628090 10. lot number identification the lot number shall be indicated on the back of the backlight case of each lcd. TCG062HVLQAVNN-GN20 - - - made in 1 2 3 4 5 year 2016 2017 2018 2019 2020 2021 code 6 7 8 9 0 1 month jan. feb. mar. apr. may jun. code 1 2 3 4 5 6 month jul. aug. sep. oct. nov. dec. code 7 8 9 x y z 11. warranty 11-1. incoming inspection please inspect the lcd within one month after your receipt. 11-2. production warranty kyocera warrants its lcd?s for a period of 12 months from the ship date. kyocera shall, by mutual agreement, replace or re-work defective lcd?s that are shown to be kyocera?s responsibility. no1. - no5. abo ve indicate 1. year code 2. month code 3. date 4. version number 5. country of origin (japan or china) spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 12 m628090 12. precautions for use 12-1. installation of the lcd 1) a transparent protection plate shall be added to protect the lcd and its polarizer 2) the lcd shall be installed so that there is no pressure on the lsi chips. 3) the lcd shall be installed flat, without twisting or bending. 4) please design the housing window so that its edges are between the active area and the effective area of the lcd screen. 5) a transparent protection sheet is attached to the polarizer. please remove the protection film slowly before use, paying attention to static electricity. 12-2. static electricity 1) since cmos ics are mounted directly onto the lcd glass, protection from static electricity is required. 2) workers should use body grounding. operator should wear ground straps. 12-3. lcd operation 1) the lcd shall be operated within the limits specified. operation at values outside of these limits may shorten life, and/or harm display images. 12-4. storage 1) the lcd shall be stored within the temperature and humidity limits specified. store in a dark area, and protect the lcd from direct sunlight or fluorescent light. 2) always store the lcd so that it is free from external pressure onto it. 12-5. usage 1) do not store in a high humidity environment for extended periods. polarizer degradation bubbles, and/or peeling off of the polarizer may result. 2) the front polarizer is easily scratched or damaged. prevent touching it with any hard material, and from being pushed or rubbed. 3) the lcd screen may be cleaned by wiping the screen surface with a soft cloth or cotton pad using a little ethanol. 4) water may cause damage or discoloration of the polarizer. clean condensation or moisture from any source immediately. 5) always keep the lcd free from condensation during testing. condensation may permanently spot or stain the polarizer. 6) do not disassemble lcd because it will result in damage. 7) this kyocera lcd has been specifically designed for use in general electronic devices, but not for use in a special environment such as usage in an active gas. hence, when the lcd is supposed to be used in a special environment, evaluate the lcd thoroughly beforehand and do not expose the lcd to chemicals such as an active gas. 8) please do not use solid-base image pattern for long hours because a temporary afterimage may appear. we recommend using screen saver etc. in cases where a solid-base image pattern must be used. 9) liquid crystal may leak when the lcd is broken. be careful not to let the fl uid go into your eyes and mouth. in the case the fluid touches your body ; rinse it off right away with water and soap. spec no. tq3c-8eaf0-e1dey71-00 part no. TCG062HVLQAVNN-GN20 page 13 m628090 13. reliability test data te st ite m te st co ndi tio n te st ti me judge me nt high temp. atmosphere 80c 240h display function display quality current consumption : no defect : no defect : no defect low temp. atmosphere -30c 240h display function display quality current consumption : no defect : no defect : no defect high temp. humidity atmosphere 40c 90% rh 240h display function display quality current consumption : no defect : no defect : no defect te mp. cycle -30c r.t. 80c 0.5h 0.5h 0.5h 10cycles display function display quality current consumption : no defect : no defect : no defect high temp. operation 70c 500h display function display quality current consumption : no defect : no defect : no defect 1) each test item uses a test lcd only once. the tested lcd is not used in any other tests. 2) the lcd is tested in circumstances in which there is no condensation. 3) the reliability test is not an out-going inspection. 4) the result of the reliability test is for your reference purpose only. the reliability test is conducted only to examine the lcd's capability. spec no. tq3c-8eaf0-e2dey71-00 date september 9, 2016 k y o c e r a i n s p e c t i o n s t a n d a r d t y p e : t c g 0 6 2 h v l q a v n n - g n 2 0 kyocera display corporation original issue date designed by : engineering dept. confirmed by : qa dept. prepared checked approved checked approved september 9, 2016 spec no. tq3c-8eaf0-e2dey71-00 part no. TCG062HVLQAVNN-GN20 page - revision record date designed by : engineering dept. confirmed by : qa dept. prepared checked approved checked approved rev.no. date page descriptions spec no. tq3c-8eaf0-e2dey71-00 part no. TCG062HVLQAVNN-GN20 page 1 visuals specification 1) note note general 1. customer identified anomalies not defined wi thin this inspection standard shall be reviewed by kyocera, and an additional standard shall be determined by mutual consent. 2. this inspection standard about the image quality shall be applied to any defect within the effective active area and shall not be applicable to outside of the area. 3. inspection conditions luminance inspection distance temperature direction : 500 lux min. : 300 mm. : 25 5 : directly above definition of inspection item dot defect bright dot defect the dot is co nstantly ?on? when power applied to the lcd, even when all ?black? data sent to the screen. inspection tool: 5% transpar ency neutral density filter. count dot: if the dot is visible through the filter . don?t count dot: if the dot is not visible through the filter . black dot defect the dot is constantly ?off? when power applied to the lcd, even when all ?white? data sent to the screen. similar size compared to bright dot. white dot (circular/foreign particle) pixel works electrically, however, circular/foreign particle makes dot appear to be ?on? even when all ?black? data is sent to the screen. adjacent dot adjacent dot defect is defined as two or more bright dot defects or black dot defects. dot defect external inspection bubble, scratch, foreign particle (polarizer, cell, backlight) visible operating (all pixels ?black? or ?white?) and non operating. appearance inspection does not satisfy the value at the spec. definition of size definition of circle size ? ( ? )/2 definition of linear size dot drawing there is an electrode in the middle of the dot and one dot is shown in the left drawing. spec no. tq3c-8eaf0-e2dey71-00 part no. TCG062HVLQAVNN-GN20 page 2 2) standard classification inspection item judgement standard defect (in lcd glass) dot defect bright dot defect acceptable number bright dot spacing : 4 : 5 mm or more black dot defect acceptable number black dot spacing : 5 : 5 mm or more 2 dot join bright dot defect acceptable number : 2 black dot defect acceptable number : 3 3 or more dots join acceptable number : 0 total dot defects acceptable number : 5 max others white dot, dark dot (circle) size (mm) acceptable number 0.2 d Q 0.2 (neglected) 0.2 d Q 0.4 5 0.4 d Q 0.5 3 0.5 d Q 0.4 0 external inspection (defect on polarizer or between polarizer and lcd glass) polarizer (scratch) width (mm) length (mm) acceptable number 0.1 w Q 0.1 (neglected) 0.1 w Q 0.3 2.0 l Q 5.0 (neglected) 5.0 l Q 5.0 0 0.3 w Q 0.3 0 polarizer (bubble) size (mm) acceptable number 0.2 d Q 0.2 (neglected) 0.2 d Q 0.3 5 0.3 d Q 0.5 3 0.5 d Q 0.4 0 foreign particle circular shape size (mm) acceptable number 0.2 d Q 0.2 (neglected) 0.2 d Q 0.4 5 0.4 d Q 0.5 3 0.5 d Q 0 .4 0 foreign particle linear shape scratch width (mm) length (mm) acceptable number 0.00 w Q 0.03 (neglected) 0.03 w Q 0.1 0 2.0 l Q 2.0 (neglected) 2.0 l Q 4.0 3 4.0 l Q 5.0 0 0.1 w Q 0.3 (according to circular shape) |
Price & Availability of TCG062HVLQAVNN-GN20
 |
|||||||||||
|
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |
