View AUIPS6021_8893079.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

automotive grade AUIPS6021( s )( r ) 1 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 intelligent power high side switch features ? over temperature shutdown (with auto - restart) ? short circuit protection (current limit) ? reverse battery protection (turns on the mosfet) ? full diagnostic capability (short circuit to battery) ? active clamp ? open l oad detection in on and off state ? ground loss protection ? logic ground isolated from power ground ? esd protection ? lead free and rohs compliant description the AUIPS6021(s)(r) is a five terminal intelligent power switch (ips) for use in a high side configurat ion. it features short circuit, over - temperature, esd protection, inductive load capability and diagnostic feedback. the output current is limited to the ilim value. the current limitation is activated until the thermal protection acts. the over - temperatur e protection turns off the device if the junction temperature exceeds the tshutdown value. it will automatically restart after the junction has cooled 7c below the tshutdown value. the reverse battery protection turns on the mosfet. a diagnostic pin provi des different voltage levels for each fault condition. the double level shifter circuitry will allow large offsets between the logic and load ground. product summary rds(on) 30m ? max. vclamp 39v i limit 32a open load 3v / 1.1a packages to - 220 d2pak d - pak auips 6 021 auips 6 021s auips 6 021r typical connection control rin load +bat input signal v diag rdgs pull - up resistors required for open load off and short circuit to vbat detection rdgp +5v out( 5) dg(4) vcc(3) in(2) gnd(1)
AUIPS6021( s )( r ) 2 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 qualification information ? qualification level automotive (per aec - q100 ?? ) comments: this family of ics has passed an automotive qualification. ir?s industrial and consumer qualification level is granted by extension of the higher automotive level. moisture sensitivity level d2pak - 5l msl1, 260c (per ipc/jedec j - std - 020) to - 220 not applicable (non - surface mount package style) dpak - 5l msl1, 260c (per ipc/jedec j - std - 020) esd machine model class m2 (+/ - 150v) ??? (per aec - q100 - 003) human body model class h1c (+/ - 1500v) ??? ( per aec - q100 - 002 ) charged device model (dpa k,d2pak) class c 4 (+/ - 900v) ??? (per aec - q100 - 011) charged device model (to220) class c 3b (+/ - 750v) ??? (per aec - q100 - 011) ic latch - up test class ii , level a (per aec - q100 - 004) rohs compliant yes ? qualification standards can be found at internationa l rectifier?s web site http://www.irf.com/ ?? exceptions to aec - q100 requirements are noted in the qualification report. ??? passing voltage level
AUIPS6021( s )( r ) 3 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 absolute maximum ratings absolute maximum ratings indicate sustaine d limits beyond which damage to the device may occur. all voltage parameters are referenced to ground lead. tj= - 40c..150c, vcc=6..35v (unless otherwise specified). symbol parameter min. max. units vout maximum output voltage vcc - 35 vcc+0.3 v voffset maximum logic ground to load ground offset vcc - 35 vcc+0.3 vin maximum input voltage - 0.3 5.5 vcc max. maximum vcc voltage ? 36 vcc cont. maximum continuous vcc voltage ? 28 vcc sc. maximum vcc voltage with short circuit protection ? 28 iin max. m aximum in current - 3 10 ma idg max. maximum diagnostic output current - 3 10 vdg maximum diagnostic output voltage - 0.3 5.5 v pd maximum power dissipation (internally limited by thermal protection) ? 25 w rth=5c/w au ips6021 rth=40c/w au ips602 1s 1?sqrt. footprint ? 3.1 rth=50c/w au ips6021r 1?sqrt. footprint ? 2.5 tj max. max. storage & operating temperature junction temperature - 40 150 c tsoldering soldering temperature (10 seconds) ? 300 c thermal characteristics symbol parameter typ. max. units rth1 thermal resistance junction to ambient au ips6021 to220 free air 50 ? c/w rth2 thermal resistance junction to case au ips6021 to220 2.6 ? rth1 thermal resistance junction to ambient au ips6021s d2pak std. footprint 60 ? rth2 therma l resistance junction to ambient au ips6021s d2pak 1? sqrt. f ootprint 40 ? rth3 thermal resistance junction to case au ips6021s d2pak 2.6 ? rth1 thermal resistance junction to ambient au ips6021r d - pak std. footprint 70 ? rth2 thermal resistance junctio n to ambient au ips6021r d - pak 1? sqrt. f ootprint 50 ? rth3 thermal resistance junction to case au ips6021r d - pak 2.6 ? recommended operating conditions these values are given for a quick design. for operation outside these conditions, please consult th e application notes. symbol parameter min. max. units vih high level input voltage 4 5.5 vil low level input voltage 0 0.9 iout continuous drain current, tambient=85c, tj=125c, vin=5v a rth=5c/w au ips6021 ? 12 rth=40c/w au ips6021s 1? sq rt. footprint ? 4.3 rth=50c/w au ips6021r 1? sqrt. footprint ? 3.9 rin recommended resistor in series with in pin 4 10 k ? rdgs recommended resistor in series with dg pin for reverse battery protection 4 20 rdgp recommended pull - up resistor for dg 4 20 rol recommended pull - up resistor for open load detection 5 100 f max. max. switching frequency ? 1.5 khz
AUIPS6021( s )( r ) 4 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 static electrical characteristics tj= - 40c..150c, vcc=6..28v (unless otherwise specified), typical values are given for vcc=14v and tj=25c symbol parameter min. typ. max. units test conditions rds(on) on state resistance tj=25c ? 24 30 m ? vin=5v, iout= 10 a on state resistance tj=150c ? 42 52 vin=5v, iout= 10 a on state resistance tj=25c, vcc=6v ? 29 36 vin=5v, iout= 5 a on state res istance during reverse battery tj=25c ? 31 39 vcc - gnd= - 14 v vcc op. operating voltage range with short circuit protection 6 ? 28 v v clamp 1 vcc to out clamp voltage 1 37 39 43 iout= 40m a v clamp 2 vcc to out clamp voltage 2 ? 40 ? iout= 8 a (see fig. 1) icc off supply current when off and vout connected to ground with r<4? ? 4 9 a vin=0v, vout=0v , tj=25c, vcc=14v icc on supply current when on ? 2.2 5 ma vin=5v , vcc=14v vih input high threshold voltage ? 2.5 3 v vil input low threshold voltage 1. 5 2 ? in hyst. input hysteresis 0.2 0.5 1 iin on input current when device is on ? 4 0 100 a vin=5v idg dg leakage current ? 0.1 10 vdg=5v vdg low level dg voltage ? 0.25 0.4 v idg=1.6ma switching electrical characteristics vcc=14v, resistive lo ad= 6 ? , vin=5v, tj= - 40c..150c, typical values are given for tj=25c symbol parameter min. typ. max. units test conditions tdon turn - on delay time ? 14 40 s see fig. 3 tr1 rise time to vout=vcc - 5v ? 10 35 tr2 rise time to vout=0.9 x vcc ? 18 65 dv/dt (on) turn on dv/dt ? 0.8 ? v/s eon turn on energy ? 250 ? j tdoff turn - off delay time ? 40 80 s tf fall time to vout=0.1 x vcc ? 15 35 dv/dt (off) turn off dv/dt ? 1.5 ? v/s eoff turn off energy ? 100 ? j
AUIPS6021( s )( r ) 5 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 protection characteristic s tj= - 40c..150c, vcc=6..28v (unless otherwise specified), typical values are given for vcc=14v and tj=25c symbol parameter min. typ. max. units test conditions ilim internal current limit 19 32 50 a vout=0v , tj=25c tsd+ over temperature high threshol d 150(1) 165 ? c see fig. 2 tsd - over temperature low threshold ? 158 ? vsc short - circuit detection voltage(2) 2 3 4 v uv+ under voltage protection vcc going up ? 5 6.2 uv - under voltage protection vcc going down ? 4.5 5.8 vol off open load de tection threshold 2 3 4 i ol on open load detection threshold 0.3 0.8 1.25 a tj= - 40..25c 0.3 0.7 1.1 tj=25..150c (1) guaranteed by design (2) reference to vcc true table operating conditions in out dg normal h h h normal l l h open load h h l open load (3) l h l short circuit to gnd h l l short circuit to gnd l l h short circuit to vcc h h l (4) short circuit to vcc (5) l h l over - temperature h l l over - temperature l l h (3) with a pull - up resistor connected between the output and vcc. (4) vds lower than 10mv. (5) without a pull - up resistor connected between the output and vcc. lead assignments
AUIPS6021( s )( r ) 6 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 functional block diagram all values are typical in vcc out 37v driver i limit 43v 150k ? i sense - + charge pump level shifter tj 165c 158c 2.5v 2.0v 6 v dg 6 v gnd ground disconnect 3v - + open load off over - temp 20mv - + open load on 3v - + short circuit 43v vcc - gnd >uv
AUIPS6021( s )( r ) 7 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 vds ids vin vcc vds clamp t clamp see application notes to evaluate power dissipation tj ilim tsd+ tsd - iout vin limiting thermal cycling dg figure 1 ? active clamp waveforms figure 2 ? protection timing diagram vout vin tr - in 90% 10% 90% 10% td on tr1 td off tf vcc - 5v tr2 vcc figure 3 ? switching times definitions figure 4 ? active clamp test circuit vclamp iout vin in vcc out r l 0v 5v 14v + - vout rem : during active clamp, vload is negative dg gnd
AUIPS6021( s )( r ) 8 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 0 5 10 15 20 25 30 -50 0 50 100 150 to220 5c/w d2pak 40c/w dpak 50c/w 50% 100% 150% 200% -50 0 50 100 150 figure 5 ? switching energy (j) vs output current (a) eon, eoff, switching energy (j) iout, output current (a) 0 200 400 600 800 1000 0 2 4 6 8 10 1 10 100 0.001 0.01 0.1 1 10 100 tj, junction temperature (c) figure 6 - normalized rds(on) (%) vs tj (c) r ds(on), drain - to - source on resistance (normalized) figure 7 ? max. output current (a) vs load inductance (mh) load inductance (mh) iout, output current (a) figure 8 ? max. ouput cur rent (a) vs ambient temperature (c) ids, cont. output current (a) tamb, ambient temperature (c) eon eoff
AUIPS6021( s )( r ) 9 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 0 10 20 30 40 50 -50 0 50 100 0.01 0.1 1 10 100 1e-5 1e-4 1e-3 1e-2 1e-1 1e+0 1e+1 1e+2 1e+3 vcc, power supply voltage (v) icc on/ icc off, supply current (a) 1.e+0 1.e+1 1.e+2 1.e+3 1.e+4 0 5 10 15 20 25 30 icc on icc off figure 11 ? icc on/ icc off (a) vs vcc (v)* figure 12 ? icc on/ icc off (a) vs tj (c)* icc on/ icc off, supply current (a) tj, junction temperature (c) 1.e+0 1.e+1 1.e+2 1.e+3 1.e+4 -50 0 50 100 150 icc on icc off *vout connected to ground with r<4? figure 10 ? i limit (a) vs jun ction temperature (c) i limit (a) figure 9 ? transient thermal impedance (c/w) vs time (s) zth, transient thermal impedance (c/w) time (s) tj, junction temperature (c)
AUIPS6021( s )( r ) 10 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 case outline - to220 (5 leads )
AUIPS6021( s )( r ) 11 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 case outline d2pak - 5 leads
AUIPS6021( s )( r ) 12 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 tape & reel d2pak - 5 leads
AUIPS6021( s )( r ) 13 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 case outline dpak - 5 leads
AUIPS6021( s )( r ) 14 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 tape & reel dpak - 5 leads
AUIPS6021( s )( r ) 15 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 part marking information ordering information base part number package type standard pack complete part number form quantity auips 6021 to220 - 5 - leads tube 50 auips 6021 auips 6021s d2 - pak - 5 - leads tube 50 auips 6021s tape and reel left 800 auips 6021 strl tape and reel right 800 auips601 1strr auips 6021r d - pak - 5 - leads tube 75 auips 6021r tape and reel 2000 a uips 6021 rtr tape and reel left 3000 auips 6021 rtrl tape and reel right 3000 auips 6021 rtrr
AUIPS6021( s )( r ) 16 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 important notice unless specifically designated for the automotive market, international rectifier corporation and its subsidiaries (ir) reserve the right to m ake corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. part numbers designated with the ?au? prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. all products are sold subject to ir?s terms and conditions of sale supplied at the time of order acknowledgment. ir warrants performance of its hardw are products to the specifications applicable at the time of sale in accordance with ir?s standard warranty. testing and other quality control techniques are used to the extent ir deems necessary to support this warranty. except where mandated by governme nt requirements, testing of all parameters of each product is not necessarily performed. ir assumes no liability for applications assistance or customer product design. customers are responsible for their products and applications using ir components. t o minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. reproduction of ir information in ir data books or data sheets is permissible only if reproduction is without alteration and i s accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alterations is an unfair and deceptive business practice. ir is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ir products or serviced with statements different from or beyond the parameters stated by ir for that product or service voids all express and any implied warranties for the associated ir product or service and is an unfair and deceptive business practice. ir is not responsible or liable for any such statements. ir products are not designed, intended, or authorized for use as components in systems intended for surgical implant into th e body, or in other applications intended to support or sustain life, or in any other application in which the failure of the ir product could create a situation where personal injury or death may occur. should buyer purchase or use ir products for any su ch unintended or unauthorized application, buyer shall indemnify and hold international rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fee s arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ir was negligent regarding the design or manufacture of the product. ir products are neith er designed nor intended for use in military/aerospace applications or environments unless the ir products are specifically designated by ir as military - grade or ?enhanced plastic.? only products designated by ir as military - grade meet military specificat ions. buyers acknowledge and agree that any such use of ir products which ir has not designated as military - grade is solely at the buyer?s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection w ith such use. ir products are neither designed nor intended for use in automotive applications or environments unless the specific ir products are designated by ir as compliant with iso/ts 16949 requirements and bear a part number including the designatio n ?au?. buyers acknowledge and agree that, if they use any non - designated products in automotive applications, ir will not be responsible for any failure to meet such requirements. for technical support, please contact ir?s technical assistance center http://www.irf.com/technical - info/ world headquarters: 101 n sepulbeda blvd., el segundo, california 90245 tel: (310) 252 - 7105
AUIPS6021( s )( r ) 17 www.irf.com ? 20 12 international rectifier f ebruary 3 , 2013 revision history revision date notes/changes b september , 12th 2011 au release c may 15, 2012 add the test condition for the icc (off) parameters d tuesday, october 16, 2012 update the date in the front page

▲Up To Search▲

Price & Availability of AUIPS6021

	To Download AUIPS6021 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .