|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 4 4 5a1 smd - 3 m arking ? hdf513 prepared checked approve d ? d a t e 200 8 - 7 - 2 3 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 9 ?? history record date spec . no . ?? part no . ??? customer no . mod ify content ? remark saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 9 1. scope this specification shall cover the characteristics of saw filter with f4 4 5a 1 used for the page system. 2. electrical specification dc voltage vdc 10v ac voltage vpp 10v50hz/60hz operation temperature - 40 to + 85 storage temperature - 45 to +85 rf power dissipation 0dbm electronic characteristics 2 - 1.typical frequency response saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 9 2 - 2.electrical characteristics part number f4 4 5a 1 unit nominal center frequency (fo) 4 4 5 mhz insertion loss 396.6mhz ~ 406.6 mhz fo fo +39.8~ fo +45. 8mhz 50min. 3 . 5 max 45 min db bandwidth - 3db 5 ~ 7 mhz ripple (with fo 5 .0mhz) 2.0max db input/output impedance(nominal) 50//0 /pf 3. test circuit saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 9 4. dimension marking hdf 513 hd: brand f : filter 513 : no. 5. environmental characteristics 5 - 1 hig h temperature exposure subject the device to +85 for 16 hours. then release the filter into the room conditions for 24 hours prior to the measurement. it shall fulfill the specifications in 2 - 2 . 5 - 2 low temperature exposure subject the device to - 4 0 f or 16 hours. then release the device into the room conditions for 24 hours prior to the measurement. it shall fulfill the specifications in 2 - 2 . 5 - 3 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +8 5 for 30 minutes. then release the device into the room conditions for 24 hours prior to the me a surement. it shall meet the specifications in 2 - 2 . 5 - 4 resistance to solder heat dip the device terminals no closer than 1.5mm into the so lder bath at 260 10 for 10 1 sec. then release the device into the room conditions for 4 hours. the device shall meet the specifications in 2 - 2 . 5 - 5 solderability subject the device terminals into the solder bath at 245 5 for 5s, more than 95% ar ea of the terminals must be covered with new solder. it shall meet the specifications in 2 - 2 . 5 - 6 mechanical shock drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2 - 2 . 5 - 7 v ibration subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the device shall fulfill the specifications in 2 - 2 . 1. ground 2. input/output 3. ground 4. ground 5. ground 6. input/output 7. ground 8. ground saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 9 6. remark 6.1 static voltage static voltage between signal load & gr ound may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultrasonic cleaning 6.3 soldering only le ads of component may be soldered. please avoid soldering another part of component. saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 9 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and stor age. 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structure (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name quantity lot n o. (3) leader part and vacant position specifications. saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 9 8. tape specifications 8.1 tensile strength of carrier tape: 4.4n/mm width 8.2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions saw filter hdf 4 4 5a1 s3 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 9 of 9 [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.0 0.3 5.5 0.05 1.75 0.1 4.0 0.1 8.0 0.1 2.0 0.05 ? 1.5 0.1 ? 1.0 0.25 0.3 0.05 2.10 0.1 6.40 0.1 5.20 0.1 [figure 2] [unit:mm] a b c d e w t r ? 3 30 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max. |
Price & Availability of HDF445A1S3 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |