high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 1 1. p art no. expression: p i f 0 6 0 5 a 1 r 0 m n a) series code e) tolerance c ode (a) (b) (c) (d) (e)(f) b) dimension code f) internal controlled code c) type code d) inductance c ode 2. c onfiguration & dimensions: unit: mm 3. s chematic: part number a b c d e f l g h pif0605 a 1r 0 mn 6.6 0.2 6.4 0.2 4.8 0.2 5 . 3 0.3 1.4 0.2 2 .60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a1r 2 mn 6.60.2 6.40.2 4.80.2 5.30.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a1r 5 mn 6.60.2 6.40.2 4.80.2 5.30.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a1r 8 mn 6.6 0.2 6.40.2 4.80.2 5.30.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a 2 r 2 mn 6.60.2 6.40.2 4.80.2 5.20.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a 3 r 3 mn 6.60.2 6.40.2 4.80.2 5.20.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a 4 r 3 mn 6.60.2 6.40.2 4.80.2 5.20.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. pif0605a 4 r 7 mn 6.60.2 6.40.2 4.80.2 5.20.3 1.40.2 2.60.25 5.6 ref. 2.5 ref. 5.6 ref. recommended pc board pattern note: 1. the above pcb layout is for reference only . 2. solder paste thickness of 0. 1 5 mm and above is recommended. l g h
high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 2 4. m aterial list: 5. g enera l specification: (a) core (b) wire (c) solder (d) ink (a) test freq. : l : 100khz/0.1v (b) operating temp. : - 40c to +125c ( including self - temperature rise) (c) storage temp. : - 40c to +125c (on board) (d) humidity range : 85 2% rh (e) heat rated current (irms) will cause the coil temperature rise approximately t of 40c (keep 1min) (f) saturation current (isat typ.) will cause l0 to drop approximately 3 0%. (g) part temperature (ambient+temp. rise) : should not exceed 125c under wors t case operating conditions. (h) storage condition (component in its packaging) i) temperature: less than 40c ii)humidity : 60% rh
high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 3 6. e lectrical characteristics: *tolerance code : m = 20% notes: 1) isat t yp. and irms typ. value is derived based from accounting the upper limit tolerance into the inductance value. 2) at all times, the current supplied to the product should not exceed isat max. value. part number inductance(uh) 20% @ 0 a i rms(a) typ. i sat (a) dcr (m) typ. dcr (m) max. @20 @40 typ. max. pif0605a1r0mn 1.00 15 20 23.0 18.0 4.1 4.52 pif0605a1r 2 mn 1.20 14 18 22.0 16.0 5.3 5.83 pif0605a1r 5 mn 1.50 13 17 19.5 14.5 5.7 6.3 pif0605a1r 8 mn 1.80 12 16 18.5 13.5 6.4 7.1 pif0605a 2 r 2 mn 2.20 10 13 16. 0 12.0 7.7 8.5 pif0605a 3 r 3 mn 3.30 8.5 11 12.5 10.0 11.2 12.5 pif0605a 4 r 3 mn 4.30 7.0 9.0 11.0 8.5 15.1 16.2 pif0605a 4 r 7 mn 4.70 6.5 8.5 10.5 8.0 16.7 18.4
high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 4 7. c haracteristics curves: pif0605a1r0mn pif0605a1r2mn pif0605a1r5mn pif0605a1r8mn pif0605a3r3mn PIF0605A2R2MN pif0605a4r3mn pif0605 a4r7mn
high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 5 8. s oldering: mildly activated rosin fluxes are preferred. the minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solde r, chip and substrate. our terminations are suitable for all re - flow soldering systems. if hand soldering cannot be avoided, the preferred technique is the utilization of hot air. 8 - 1 solder re - flow: recommended temperature profiles for re - flow soldering in figure 1. 8 - 2 soldering iron (figure 2): products attachment with soldering iron is discouraged due to the inherent process control limitations. in the event that a soldering iron must b e employed the following precautions are recommended. note : a) preheat circuit and products to 150c. b) 355c tip temperature (m ax . ) c) never contact the ceramic with the iron tip d) 1.0m m tip diameter (m ax . ) e) use a 20 watt soldering iron with tip diameter of 1.0mm f) limit soldering time to 4~5 secs.
high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 6 9. p ackaging information: 9 - 1 reel dimension 9 - 2 tape dimension 9 - 3 packaging quantity type a(mm) b(mm) c(mm) d(mm) 13 x16 mm 16 . 4+2/ - 0 1002 13. 0 + 0.5 / - 0.2 330 pif 0605 a chip / reel 8 00 inner box 1,6 00 carton 6,4 00 series size ao(mm) bo(mm) ko(mm) p(mm) w(mm) f(mm) t(mm) d (mm) pif 0605 a 6 . 8 0.1 7 . 0 0.1 5 .30.1 12 .00.1 16 0.3 7 .50.1 0.350.1 1 .50.1
high current power inductor C pif0605 a s eries propri etary and confidential document of superworld 04 / 0 5 /201 6 p 7 9 - 4 tearing off force application notice: 1. storage conditions: to maintain the solderabililty of terminal electrodes: a) recommended products should be used with in 12 months from the time of delivery. b) the packaging material should be kept where no chlorine or sulfur exists in the air. 2. transportation: a) products should be handled with care to avoid damage or cont amination from perspirat ion and skin oils. b) vacuum pick up is strongly recommended for individual components. c) bulk handling should ensure that abrasion and mechanical shock are minimized. the force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions room temp. ( ) room humidity (%) room atm (hpa) tearing speed mm/min 5~35 45~85 860~1060 300
|
