View A050VW01-V0_7868243.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

version: 0.4 page: 0/25 customer approval sheet company name model a050vw01 v0 customer approved title : name : approval for specifications only (spec. ver. ) approval for specifications and es sample (spec. ve r. ) approval for specifications and cs sample (spec. ve r. ) customer remark : auo pm : p/n : 97.05a07.000 comment : www.datasheet.co.kr datasheet pdf - http://www..net/
all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. doc. version : 0.4 total pages : 25 date : 2008/07/22 product specification 5.0" color tft-lcd module model name: a050vw01 v0 < >preliminary specification < >final specification note: the content of this specification is subject to change. ? 2008 au optronics all rights reserved, do not copy. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 1/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. record of revision version revise date page content 0.0 2008/03/05 first draft. 0.1 2008/05/06 3 add actual weight. 17 modify packing form. 9-10 modifty timing parameters value and power on/ off sequence. 0.2 2008/05/07 6 modify led voltage value as the reference value. 16 correct ra test vibration temperature. 0.3 2008/07/07 change the format to standard format. 0.4 2008/07/22 3 modify power consumption www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 2/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. contents a. general information ................................ ................................................... ..................................................3 b. outline dimension .................................. ................................................... ..................................................4 1. tft-lcd module ? front view..................... ................................................... ............................................4 2. tft-lcd module ? rear view ...................... ................................................... ...........................................5 c. electrical specifications.......................... ................................................... .................................................6 1. tft lcd panel pin assignment.................... ................................................... ...........................................6 2. absolute maximum ratings ........................ ................................................... ..............................................8 3. electrical dc characteristics................... ................................................... .................................................8 4. electrical ac characteristics ................... ................................................... ...............................................10 5. power on/off characteristics .................... ................................................... .............................................12 d. optical specification.............................. ................................................... .................................................14 e. touch screen panel specifications .................. ................................................... ....................................17 1. fpc pin assignment.............................. ................................................... .................................................17 2. electrical characteristics ...................... ................................................... ..................................................1 7 3. mechanical characteristics ...................... ................................................... ..............................................18 4. life test condition ............................. ................................................... ................................................... ..18 5. attention....................................... ................................................... ................................................... ........19 f. reliability test items............................. ................................................... ..................................................2 0 g. packing and marking ................................ ................................................... ..............................................23 1. packing form .................................... ................................................... ................................................... ..23 2. module/panel label information.................. ................................................... ...........................................24 3. carton label information ........................ ................................................... ................................................24 h. precautions........................................ ................................................... ................................................... ...25 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 3/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. a. general information this product is for pnd and mid applications. no. item unit specification remark 1 screen size inch 5.0(diagonal) 2 display resolution dot 800rgb(h)480(v) 3 overall dimension mm 119.6(h) 76.5(v) 4.05(t) note 1 4 active area mm 108.0(h)64.8(v) 5 pixel pitch mm 0.045(h)0.135(v) 6 color configuration -- r. g. b. stripe note 2 7 color depth -- 16.7m colors note 3 8 ntsc ratio % 50 9 display mode -- normally white 10 panel surface treatment -- anti-glare, 3h 11 weight g 76.6 12 panel power consumption w 1.5 note 4 13 backlight power consumption mw 896 14 viewing direction 6 o?clock (gray inversion) note 1: not include fpcs. refer next page to get fu rther information. note 2: below figure shows dot stripe arrangement. note 3: the full color display depends on 24-bit da ta signal (pin 5~28). note 4: please refer to electrical characteristics chapter. ?????????? ?? . ?????????? ?? . ???? ? ? ? ( 1 2 3??????????? .2398 2399 2400) (1???????? ..480) www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 4/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. b. outline dimension 1. tft-lcd module ? front view www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 5/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. 2. tft-lcd module ? rear view www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 6/25 c. electrical specifications 1. tft lcd panel pin assignment recommended connector : fh12-50s-0.5sh pin no. symbol type description remark 1 gnd p ground for digital circuit 2 gnd p ground for digital circuit 3 vdd p dc-dc circuit supply voltage 4 vdd p dc-dc circuit supply voltage 5 dr0 i red data input; lsb 6 dr1 i red data input 7 dr2 i red data input 8 dr3 i red data input 9 dr4 i red data input 10 dr5 i red data input 11 dr6 i red data input 12 dr7 i red data input; msb 13 dg0 i green data input; lsb 14 dg1 i green data input 15 dg2 i green data input 16 dg3 i green data input 17 dg4 i green data input 18 dg5 i green data input 19 dg6 i green data input 20 dg7 i green data input; msb 21 db0 i blue data input; lsb 22 db1 i blue data input 23 db2 i blue data input 24 db3 i blue data input 25 db4 i blue data input 26 db5 i blue data input 27 db6 i blue data input 28 db7 i blue data input; msb www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 7/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 29 gnd p ground for digital circuit 30 dclk i data clock input 31 disp i standby mode control pin. normally pull high. disp = ?1?, normal operation. disp = ?0?, standby mode. 32 nc - not connected. please leave it open. 33 nc - not connected. please leave it open. 34 de i data enable input. active level is high. 35 u/d i u/d = ?1?, down scan. u/d = ?0?, up scan. 36 nc - no connection. please leave it open 37 gnd p ground for digital circuit 38 gnd p ground for digital circuit 39 x1 i/o touch panel right electrode (r) 40 y2 i/o touch panel bottom electrode (b) 41 x2 i/o touch panel left electrode (l) 42 y1 i/o touch panel top electrode (u) 43 nc - no connection. please leave it open 44 nc - no connection. please leave it open 45 nc - no connection. please leave it open 46 vled- p backlight led cathode 47 vled+ p backlight led anode 48 gnd p ground for digital circuit 49 gnd p ground for digital circuit 50 gnd p ground for digital circuit note 1: i: input; o: output; p: power. note 2: for correct power on sequence please refer to section 5 ?power on/off sequence? www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 8/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. absolute maximum ratings item symbol condition min. max. unit remark power voltage vdd gnd=0 -0.3 4.5 v note 1 input signal voltage data gnd=0 -0.3 vdd+0.3 v digital signal note 1: functional operation should be restricted u nder ambient temperature (25 ). note 2: maximum ratings are those values beyond whi ch damages to the device may occur. functional operation should be restricted to the limits in the electrical characteristics chapter. 3. electrical dc characteristics a. typical operation condition (agnd =gnd = 0v) item symbol min. typ. max. unit remark power supply vdd 3.1 3.3 3.5 v input high voltage vih 0.7*vdd - vdd v input low voltage vil 0 - 0.3*vdd b. current consumption (agnd=gnd=0v) parameter symbol condition min. typ. max. unit remark i vdd vdd=3.3v - 90 110 m a note 1, 2 input current for vdd i vdd (standby) vdd=3.3v - 10 50 ua note 3 note 1: test condition is under typical electrical dc and ac characteristics. note 2: test pattern is the following picture (colo r bar). note 3: in standby mode, all digital signals are st opped. ex. dclk, de ...etc. c. backlight driving conditions the backlight (led module, note 1) is suggested to drive by constant current with typical value. parameter symbol min. typ. max. unit remark led current i l -- 20 22 ma note 1 power p l -- 896 1108 mw led life time l l 10,000 -- -- hr note 2, 3 note 1: led backlight is two parallel strings and o ne led for each string is as below figure. suggest drive by 20ma for each led string. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 9/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 22.4 v i l i l note 2: define ?led lifetime?: brightness is decrea sed to 50% of the initial value. led lifetime is restricted under normal condition, ambient temperat ure = 25 and led lightbar current = 20 ma. note 3: if it uses larger led lightbar voltage/ cur rent more than 20ma, it maybe decreases the led lifetime. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 10/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 4. electrical ac characteristics a. signal ac characteristics parameter symbol min. typ. max. unit remark dclk duty cycle -- 40 50 60 % t cw / t dclk x100% de setup time t est 8 -- -- ns de hold time t ehd 8 -- -- ns data setup time t dst 8 -- -- ns data hold time t dhd 8 -- -- ns // 70% t cw t dclk 1st 2nd last // // t dhd t dst 70% 70% 30% 30% dclk data bus de 70% 30% t est // 70% t dclk : dclk period t cw : the width of dclk high b. timing diagram 1. vertical timing of input www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 11/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. horizontal timing of input c. timing parameters parameter symbol min typ max unit clock cycle 1/t dclk - 30 50 mhz horizontal cycle 1/th - 32.33 - khz vertical cycle 1/tv - 61.58 - hz horizontal signal horizontal cycle *1 th 880 928 1100 dclk horizontal display period thd - 800 - dclk horizontal blank thb 80 128 300 dclk vertical signal vertical cycle tv 500 525 680 h vertical display period tvd - 480 - h vertical blank tvb 20 45 200 h www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 12/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. 5. power on/off characteristics a. recommended power on sequence the lcd adopts high voltage driver ic, so it could be permanently damaged under a wrong power on/off sequ ence. the suggested lcd power sequence is below: power on sequence: vdd dclk disp led unit. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 13/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. b. recommended power off sequence power off sequence: led unit disp dclk vdd. signals dclk, disp and de must be pulled low at power on. any power on glitches at these signals can cause abno rmal display. below is an example of de signal demonstrating a signal glitch power on an d a correct signal power on. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 14/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. d. optical specification all optical specification is measured under typical condition (note 1, 2) item symbol condition min. typ. max. unit remark response time rise fall tr tf =0 -- -- 15 20 20 25 ms ms note 3 contrast ratio cr at optimized viewing angle 250 300 -- note 4 top bottom left viewing angle right cr 10 -- -- -- -- 45 55 60 60 -- -- -- -- deg. note 5 brightness y l =0 350 400 -- cd/m 2 note 6 x =0 0.26 0.31 0.36 white y =0 0.28 0.33 0.38 x =0 0.585 0.635 0.685 red y =0 0.300 0.350 0.400 x =0 0.285 0.335 0.385 green y =0 0.485 0.535 0.585 x =0 0.095 0.145 0.195 chromaticity blue y =0 0.050 0.100 0.150 uniformity y l % 70 75 -- % note 7 note 1: measured under ambient temperature =25 , and led lightbar current i l = 20ma in the dark room. note 2: to be measured on the center area of panel with a viewing cone of 1 by topcon luminance meter bm-5a, after 15 minutes operation. center of the screen field=1 bm-5a www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 15/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 3: definition of response time: the output signals of photo detector are measured when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time is defined as the time interval between the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% note 4.definition of contrast ratio: contrast ratio is calculated with the following fo rmula. status black" " at is lcd when output detector photo status white" " at is lcd when output detector photo (cr) ratio contrast = note 5. definition of viewing angle, , refer to figure as below. x' y x y' www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 16/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. x' y x y' x' y x y' note 6: measured at the center area of the panel wh en all the input terminals of lcd panel are electrically opened. note 7: luminance uniformity of these 9 points is d efined as below: 9) - (1 points 9 in luminance maximum 9) - (1 points 9 in luminance minimum uniformity = www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 17/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. e. touch screen panel specifications 1. fpc pin assignment pin no. symbol i/o description 1 x1 i/o touch panel right electrode (r) 2 y2 i/o touch panel bottom electrode (b) 3 x2 i/o touch panel left electrode (l) 4 y1 i/o touch panel top electrode (u) 2. electrical characteristics item min. typ max. unit remark rate dc voltage -- -- 7 v x (film) 300 -- 1350 resistance y (glass) 100 -- 700 at connector linearity -1.5% 1.5% -- note 1 response time 30 ms insulation resistance 20 m dc 25v note 1: measurement condition of linearity: differe nce between actual voltage & theoretical voltage is an error at any points. linearity is the value of t he max. error voltage divided by voltage difference on active area. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 18/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 3. mechanical characteristics item min. max. unit remark hardness of surface 3 -- h jis k-5600 operation force (pen or finger) 80 gf note 1, 2 note 1: within ?active area?, but not near the acti ve area boundary and on the dot-spacer. note 2: operation force measurement is under test c ondition as figure below. 4. life test condition item min. max. unit remark notes life 10 5 -- lines note 1, 2 input life 10 6 -- times note 1, 3 note 1: notes life test condition (by pen): slide o n central 2/3 of active area and use r 0.8mm polyacecal pen, input force : 250gf, frequency : 60 mm/sec. sliding from a to b complete 1 time. shown as figure2. note 2: input life test condition (by finger): test position on active area center and use r8.0mm sili con rubber (hardness 60 ), test force: 250gf, frequency : 2times/sec. shown as figure. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 19/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 5. attention please pay attention for below matters at mounting design of touch panel of lcd module. 1) in order to avoid the incorrect or abnormal inp ut, please design the casing opening area out of th e touch panel area. suggest casing opening area shown as mechanical drawing. suggest the gap between casing and touch panel surface at least 0.5 mm to avoid incorrect input. 2) cushion area must not contact with active area. suggest cushion area shown as mechanical drawing. 3) use elastic or non-conductive material to enclo sure touch panel. 4) do not bond film of touch panel with casing. 5) the touch panel edge is conductive. do not touc h it with any conductive part after mounting. 6) if user wants to cleaning touch panel by air gu n, pressure 2kg/cm 2 below is suggested. not to blow glass from fpc site to prevent fpc peeled off. 7) do not put a heavy shock or stress on touch pan el and film surface. ex. don?t lift the panel by th e vacuum nozzle. 8) do not lift lcd module by fpc. 9) please use dry cloth or soft cloth with neutral detergent (after wring dry) or one with ethanol at cleaning. do not use any organic solvent, acid or a lkali liquor. 10) do not pile touch panel. do not put heavy good s on touch panel. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 20/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. f. reliability test items no. test items conditions remark 1 high temperature storage ta= 80 240hrs 2 low temperature storage ta= -30 240hrs 3 high ttemperature operation tp= 70 240hrs 4 low temperature operation ta= -20 240hrs 5 high temperature & high humidity tp= 60 . 90% rh 240hrs operation 6 heat shock -25 ~70 , 50 cycle, 2hrs/cycle non-operation 7 electrostatic discharge contact = 4 kv, class b air = 8 kv, class b note 5 frequency range : 10 ~ 55 hz stoke : 1. 5 mm sweep : 10hz~55hz~10hz 2 hours for each direction of x,y,z 8 vibration 4 hours for y direction non-operation jis c7021, a-10 condition a : 15 minutes 9 mechanical shock 100g . 6ms, x,y,z 3 times for each direction non-operation jis c7021, a-7 condition c 10 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz ?6db/octave from 200~500hz iec 68-34 11 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces 12 pressure 5kgf, 5sec note 6 note 1: ta: ambient temperature. tp: panel surface temperature note 2: in the standard conditions, there is not di splay function ng issue occurred. all the cosmetic specification is judged before the reliability stre ss. note 3: all the cosmetic specification is judged be fore the reliability stress. note 4: temperature and relative humidity range is shown in the figure below www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 21/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 5 : all test techniques follow iec6100-4-2 sta ndard. test condition note pattern procedure and set-up contact discharge 330 ? , 150pf, 1sec, 8 point, 25times/point air discharge 330 ? , 150pf, 1sec, 8 point, 25times/point criteria b ? some performance degradation allowed. no data l ost. self-recoverable hardware failure. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 22/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 6: the panel is tested as figure. the jig is 10 mm made by copper with rubber and the loading speed is 3mm/min on position a~e. after the conditi on, no glass crack will be found and panel function check is ok.( no guarantee lc mura lc bubble) loading lcm www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 23/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. g. packing and marking 1. packing form www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 24/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. module/panel label information the module/panel (collectively called as the ?produ ct?) will be attached with a label of shipping numb er which represents the identification of the product at a specific location. refer to the product outli ne drawing for detailed location and size of the label. the label is composed of a 22-digit serial number with the f ollowing definition: example: 501m06zl06123456781z05: product manufacturing week code: wk50 product version: version 1 product manufactuing factory: m06 3. carton label information the packing carton will be attached with a carton l abel where packing q?ty, auo model name, auo part number, customer part number (optional) and a serie s of carton number in 13 or 14 digits are printed. the carton number is apparing in the following format: refer to the drawing of packing format for the loca tion and size of the carton label. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.4 page: 25/25 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. h. precautions 1. do not twist or bend the module and prevent the unsuitable external force for display module during assembly. 2. adopt measures for good heat radiation. be sure to use the module with in the specified temperature . 3. avoid dust or oil mist during assembly. 4. follow the correct power sequence while operatin g. do not apply the invalid signal, otherwise, it w ill cause improper shut down and damage the module. 5. less emi: it will be more safety and less noise. 6. please operate module in suitable temperature. t he response time & brightness will drift by differe nt temperature. 7. avoid to display the fixed pattern (exclude the white pattern) in a long period, otherwise, it will cause image sticking. 8. be sure to turn off the power when connecting or disconnecting the circuit. 9. polarizer scratches easily, please handle it car efully. 10. display surface never likes dirt or stains. 11. a dewdrop may lead to destruction. please wipe off any moisture before using module. 12. sudden temperature changes cause condensation, and it will cause polarizer damaged. 13. high temperature and humidity may degrade perfo rmance. please do not expose the module to the direct sunlight and so on. 14. acetic acid or chlorine compounds are not frien ds with tft display module. 15. static electricity will damage the module, plea se do not touch the module without any grounded device. 16. do not disassemble and reassemble the module by self. 17. be careful do not touch the rear side directly. 18. no strong vibration or shock. it will cause mod ule broken. 19. storage the modules in suitable environment wit h regular packing. 20. be careful of injury from a broken display modu le. 21. please avoid the pressure adding to the surface (front or rear side) of modules, because it will c ause the display non-uniformity or other function issue. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of A050VW01-V0

	To Download A050VW01-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .