page . 1 december 24,2013-rev.01 DI200~di2010 ? plastic material used carries underwriters laboratory recognition 94v-o ? low leakage ? surge overload rating--50 amperes peak ? ideal for printed circuit board ? exceeds environmental standards of mil-s-19500/228 ? lead free in compliance with eu rohs 2011/65/eu directives ? green molding compound as per iec61249 std. . (halogen free) mechanical data ? case: reliable low cost construction utilizing molded plastic technique results in inexpensive product ? terminals: lead solderable per mil-std-750, method 2026 ? polarity: polarity symbols molded or marking on body ? weight: 0.0115 ounce, 0.3268 gram dual-in-line glass passivated single-phase bridge rectifier maximum ratings and electrical characteristics ratings at 25c ambient temperature unless otherwise specified.single phase, half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20% notes: 1. measured at 1 mhz and applied reverse voltage of 4 volts 2. thermal resistance from junction to ambient and from junction to lead mounted on p.c.b. with 0.5 x 0.5"(13 x 13mm) copper pa ds features voltage 50~1000 volt 2 ampere current parameter symbol DI200 di201 di202 di204 di206 di208 di2010 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms bridge input voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward current t a =40 o ci f(av) 2a peak forward surge current : 8.3ms single half sine-wave superimposed on rated load i fsm 50 a i 2 t rating for fusing (t<8.35ms) i 2 t10a 2 s maximum forward voltage drop per bridge element at 2a v f 1.1 v maximum dc reverse current at rated dc blocking voltage t j =25 o c t j =125 o c i r 5 500 ? a typical junction capacitance (note 1) c j 25 pf typical thermal resistance per leg (note 2) r ? ja r ? jl 40 15 o c / w operating junstion and storage temperature range t j ,t stg -55 to + 150 o c 0.335(8.51) 0.316(8.05) 0.315(8.00) 0.285(7.24) 0.255(6.5) 0.245(6.2) 0.350(8.9) 0.300(7.6) 0.045(1.14) 0.035(0.89) 0.022(0.56) 0.018(0.46) 0.075(1.90) 0.055(1.39) 0.185(4.69) 0.150(3.81) 0.098(2.5) 0.086(2.2)
page . 2 december 24,2013-rev.01 DI200~di2010 fig.1 derating curve for output rectified current fig.3 typical reverse characteristics ambient temperature, c o percent of peak reverse voltage, % average forward output current, amperes instantaneous reverse current,ua rating and characteristic curves 3.0 2.0 1.0 0 0 50 100 150 1.5 2.5 0.5 t = 100 c a o t=25 c a o 10 1.0 0.1 0.01 0 20 40 60 80 100 120 140 fig.2 typical instantaneous forward characteristics fig.4 maximum non-repetitive peak forward surge current no. of cycles at 60hz instantaneous forward voltage, volts instantaneous forward current, amperes forward surge current,amperes pk (half sine-wave) 0 .01 .1 1.0 10 0.2 0.4 0.6 0.8 1.0 1.2 1.4 100 60 60 50 70 40 40 30 20 20 10 10 5 2 1 0
page . 3 december 24,2013-rev.01 DI200~di2010 part no_packing code_version DI200_t0_00001 for example : rb500v-40 _ r2 _ 00001 part no. serial number version code means hf packing size code means 13" packing type means t/r packing code xx version code xxxxx packing type 1 st code packing size code 2 nd code hf or rohs 1 st code 2 nd ~5 th code tape and ammunition box (t/b) a n/a 0 hf 0 serial number tape and reel (t/r) r 7" 1 rohs 1 serial number bulk packing (b/p) b 13" 2 tube packing (t/p) t 26mm x tape and reel (right oriented) (trr) s 52mm y tape and reel (left oriented) (trl) l panasert t/b cathode up (pbcu) u forming f panasert t/b cathode down (pbcd) d
page . 4 december 24,2013-rev.01 DI200~di2010 disclaimer ? reproducing and modifying information of the document is prohibited without permission from panjit international inc.. ? panjit international inc. reserves the rights to make changes of the content herein the document anytime without notification. please refer to our website for the latest document. panjit international inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. ? panjit international inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. ? applications shown on the herein document are examples of standard use and operation. customers are responsible in comprehending the suitable use in particular applications. panjit international inc. makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. ? the products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify panjit international inc. for any damages resulting from such improper use or sale. ? ? since panjit uses lot number as the tracking base, please provide the lot number for tracking when complaining.
|
