designed & dimensioned in millimeters[inches] h petc-xx-xx-xx-01-x-ra-xx power positions (per end) -01, -02, -04 right angle signal positions -12 -40 plating specification -s: selective gold on contact/ matte tin on tail -t: matte tin -l: light selective gold on contact/ matte tin on tail option -sd: screw down (see fig 1, sht 1) -lc: locking clip (use lc-11-tm) (see fig 2, sht 2) -01, -02, -04 power positions (per end) * * * * - see table 1 for available combinations -01 lead style ** ** 14.50 .571 ref 0.50 (typ) ref .020 5.72 (typ) .225 11.43 .450 (typ) 2.54 (typ) .100 "b" (see table 2) 22.86 .900 (9 spaces @ 2.54 [.100]) 2.54 (typ) .100 "d" (see table 2) 3 max sway (typ) (either direction) "a" "a" "b" "b" pet-02-ra-sd-40 c c c c 01 04 "c" (see table 2) 3.81 .150 (typ) ref 17.98 .708 ref "a" ref (see table 2) 23.50 .925 ref do not scale from this print "f" "f" 6.60 .260 ref 1.17 .046 ref 0.64 (typ) ref .025 2.35 ref .093 5.76 0.20 .227 .008 2.51 (typ) .099 section "a"-"a" sub-t-1m34-01-xx c 2.70 (typ) .106 section "b"-"b" c 6.60 (typ) .260 2.35 (typ) ref .093 0.64 sq ref .025 5.76 0.20 .227 .008 2.54 (typ) .100 2.54 (typ) .100 section "f"-"f" t-1s64-11-x t-1s64-12-x t-1s64-13-x t-1s64-14-x c c fig 1 petc-01-40-01-x-ra-sd shown max - blank only for existing customers sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: right angle power terminal by: petc-xx-xx-xx-01-x-ra-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 1/12/2006 2 1 sheet scale: 1:0.666667 insulator: lcp, color: black terminal: copper alloy f:\dwg\misc\mktg\petc-xx-xx-xx-01-x-ra-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: 2.22n [.5 lb]. 4. parts to be packaged in trays. 5. parts placed in tray with pin #1 facing the right side, due to pin numbering order. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
h 3.50 .138 2.75 .108 (measure at tip of pin) "c" (see table 2) 3 max sway (typ) (either direction) pet-02-ra-lc-40 lc-11-tm c 8.23 .324 ref fig 2 petc-01-40-01-01-x-ra-lc shown (same as fig 1, unless otherwise stated) 0.64 (typ) ref .025 3 max sway (typ) (either direction) 6.35 (typ) .250 "b" (see table 2) "a" ref (see table 2) "d" (see table 2) fig. 3 petc-02-40-02-01-x-ra-sd shown (same as fig. 1, unless otherwise stated) c pet-04-ra-sd-40 "b" (see table 2) 6.35 (typ) .250 "a" ref (see table 2) "d" (see table 2) fig. 4 petc-04-40-04-01-x-ra-sd shown (same as fig. 1, unless otherwise stated) c pet-08-ra-sd-40 sheet of right angle power terminal by: petc-xx-xx-xx-01-x-ra-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing clay w 1/12/2006 2 2 sheet scale: 1.5:1 revision h f:\dwg\misc\mktg\petc-xx-xx-xx-01-x-ra-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|