axmw 8596 www.axtal.com wasemweg 5 page 1(5) fon: +49 (6261) 939834 d-74821 mosbach fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg specification AXMW8596 issue: 01 date: 2005-02-01 oscillator type : crystal co ntrolled microwave oscillator parameter min. typ. max. unit condition frequency range 8.5 9.6 ghz standard frequencies 6 frequencies within 4% frequency stability ppm initial tolerance -50 50 ppm @25c vs. temperature in operating frequency range (steady state) -100 100 ppm -40~+70c medium term (aging) over 24 hours -1 1 ppm @ constant temp. frequency selection electronic frequency control by grounding of appropriate selection pin note 2 rf output signal waveform sinus load 50 ohm load vswr 1.5 output power 50 mw output power variation 2 3 2 db db db 0c ~ +70c -30c ~ +70c between 6 frequencies spurious outputs (note 1) 50 65 90 db fc 5 mhz outside fc 5 mhz am noise (note 1) -90 -75 dbc dbc fc 30 mhz ~60 mhz elsewhere fm noise (note 1) -68 dbc fc 30 mhz ~60 mhz vibration sensitivity 10 hz / g see graph 1 supply voltage v s 27.5 28.0 28.5 v current consumption (steady state) 600 ma power line ripple noise (pk-pk) 500 mv 50 hz ~ 200 mhz relative humidity 80 100 % % continuous during warm-up storage temperature range -55 +85 c 95% r.h. enclosure l x w x h (see drawing) 100 x 70 x 30 mm weight tbd gram packing bulk esd sensitivity 1500 v hbm as in iec 61000- 4-2 notes: 1. terminology and test conditions are according to iec standard iec60679-1, unless otherwise stated 2. channel selection by connecting ground (pin 7) to one of the 6 pins in viking connector vr7/4ab13 the six nominated frequencies to be determined by the purchasing-order
axmw 8596 www.axtal.com wasemweg 5 page 2( 5) fon: +49 (6261) 939834 d-74821 mosbach fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg enclosure drawing: mounting plate: pin connections: vr7/4ab13 connector: pin # symbol function 1 ch1 channel 1 select 2 ch2 channel 2 select 3 ch3 channel 3 select 4 ch4 channel 4 select 5 ch5 channel 5 select 6 ch6 channel 6 select 7 ground sma connector: rf output bnc connector : v s supply voltage marking: AXMW8596 axtal ww/xx & serial number environmental conditions: vibration : specification must be met under the vibrati on conditions of the chart below (graph 1). shock : half sine 15 g, 11 ms in 3 mutually perpendi cular axes. no damage. shock not applied to short term stability requirements
typical spectrum drawing 1 : typical spectrum drawing 2: c l r w r a r e f 2 0 d b m a t t 4 5 d b 1 a p 2 0 0 k h z / c e n t e r 9 . 0 7 g h z s p a n 2 m h z * * r b w 1 0 k h z v b w 5 0 h z s w t 8 s - 8 0 - 7 0 - 6 0 - 5 0 - 4 0 - 3 0 - 2 0 - 1 0 0 1 0 2 0 axtal gmbh & co. kg wasemweg 5 d-74821 mosbach AXMW8596 page 3(5) www.axtal.com info@axtal.com fon: +49 6261 939834 fax: +49 6261 939836
c l r w r a r e f 2 0 d b m a t t 4 5 d b 1 0 0 k h z / c e n t e r 9 . 0 1 5 0 0 6 g h z s p a n 1 m h z r b w 2 0 k h z v b w 2 k h z s w t 5 0 m s 1 s a - 8 0 - 7 0 - 6 0 - 5 0 - 4 0 - 3 0 - 2 0 - 1 0 0 1 0 2 0 1 m a r k e r 1 [ t 1 f x d ] 1 7 . 6 6 d b m 9 . 0 1 5 0 0 4 3 9 7 g h z 2 d e l t a 2 [ t 1 p h n ] - 9 1 . 3 7 d b c / h z 9 9 . 3 5 8 9 7 4 3 6 0 k h z p h n 1 7 . 6 1 6 d b m p h n r e f 2 0 d b m a t t 4 5 d b c l r w r a 1 a p r b w 3 m h z v b w 3 0 0 k h z s w t 1 5 5 m s c e n t e r 1 3 . 2 5 g h z s p a n 2 6 . 5 g h z 2 . 6 5 g h z / - 8 0 - 7 0 - 6 0 - 5 0 - 4 0 - 3 0 - 2 0 - 1 0 0 1 0 2 0 1 m a r k e r 1 [ t 1 ] - 3 9 . 2 8 d b m 5 0 0 . 0 0 0 0 0 0 0 0 0 m h z axtal gmbh & co. kg wasemweg 5 d-74821 mosbach AXMW8596 page 4(5) www.axtal.com info@axtal.com fon: +49 6261 939834 fax: +49 6261 939836
typical pll settling time during switch from channel 1 to channel 6: typical pll settling time during switch from channel 6 to channel 1: typical pll settling time during switc h from channel 2 to channel 3: axtal gmbh & co. kg wasemweg 5 d-74821 mosbach AXMW8596 page 5(5) www.axtal.com info@axtal.com fon: +49 6261 939834 fax: +49 6261 939836
|
