![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
product specification lp097x02 liquid crystal display specification for approval title 9.7" xga tft lcd customer model supplier lg display co., ltd. *model lp097x02 suffix sla3 ( ) preliminary specification ( ) final specification ver. 0.1 23. apr. 2010 1 / 28 suffix sla3 *when you obtain standard approval, please use the above model name without suffix approved by signature // / please return 1 copy for your confirmation with your signature and comments. j. k. kim / s. manager product engineering dept. lg display co., ltd approved by signature reviewed by prepared by k. t. moon / manager h. h. lee / engineer www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp097x02 liquid crystal display contents no item page cover 1 contents 2 record of revisions 3 1 general description 4 2 absolute maximum ratings 5 3 electrical specifications 3-1 electrical charactreistics 6 3-2 interface connections 7 3-3 lvds signal timing specifications 8 3 - 4 signal timing specifications ver. 0.1 23. apr. 2010 2 / 28 3 - 4 signal timing specifications 10 3-5 signal timing waveforms 10 3-6 color input data refernece 11 3-7 power sequence 4 optical sfecifications 13 5 mechanical characteristics 17 6 reliablity 21 7 international standards 7-1 safety 22 7-2 emc 22 8 packing 8-1 designation of lot mark 23 8-2 packing form 23 9 precautions 24 a appendix. enhanced extended display identification data 26 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display record of revisions revision no revision date page description edid ver 0.1 23. apr. 2010 - first draft 1.0 ver. 0.1 23. apr. 2010 3 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 1. general description the lp097x02 is a color active matrix liquid crystal display with an integral led backlight system. the matrix employs a-si thin film transistor as the active eleme nt. it is a transmissive type display operating in the normally black mode. this tft-lcd has 9.7 inches diagona lly measured active display area with xga resolution(1024 horizontal by 768 vertical pixel array). e ach pixel is divided into red, green and blue sub- pixels or dots which are arranged in vertical stripes. gray s cale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. the lp097x02 has been designed to apply the interface method that enables low power, high speed, low emi. the lp097x02 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. in combination with the ver tical arrangement of the sub-pixels, the lp097x02 characteristics provide an excellent flat display for offi ce automation products such as notebook pc. tft-lcd panel (1024 x 768) 1 768 cn 1 user connector power block gate driver lvds & timing control block (log_b type) (log_b type) (log_b type) (log_b type) ver. 0.1 23. apr. 2010 4 / 28 general features active screen size 9.7 inches diagonal outline dimension 210.53(h) 166.53 (v) 3.55(d, max.) mm pcb area : 5.82(max.) pixel pitch 0.192 mm 0.192 mm pixel format 1024 horiz. by 768 vert. pixels rgb str ip arrangement color depth 6-bit, 262,144 colors luminance, white 400 cd/m 2 (typ., @i led =20ma) power consumption logic : 0.8w(typ.@mosaic), back li ght : 2.1w (typ.@ i led = 20ma) weight 160g (max.) display operating mode transmissive mode, normally bl ack surface treatment glare, anti-reflective treatment o f the front polarizer, 3h control & data power edid signal & power 768 1 1024 user connector 30 pin block edid block source driver circuit led backlight ass y 6leds x 6 strings www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 2. absolute maximum ratings the following are maximum values which, if exceeded , may cause faulty operation or damage to the unit. table 1. absolute maximum ratings 90 % 80 % parameter symbol values units notes min max power input voltage vcc -0.3 4.0 vdc at 25 5 c operating temperature t op 0 50 c 1 storage temperature h st -20 60 c 1 operating ambient humidity h op 10 90 %rh 1 storage humidity h st 10 90 %rh 1 note : 1. temperature and relative humidity range a re shown in the figure below. wet bulb temperature should be 39 c max, and no condensation of water. ver. 0.1 23. apr. 2010 5 / 28 storage operation 10 20 30 40 50 60 70 80 0 -20 dry bulb temperature [ ] 10 % 20 % 40 % 60 % 90 % 80 % 0 10 20 30 40 50 60 wet bulb temperature [ ] humidity[(%)rh] www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 3. electrical specifications 3-1. electrical characteristics table 2. electrical characteristics parameter symbol values unit notes min typ max module : power supply input voltage vcc 3.0 3.3 3.6 v dc power supply input current i cc mosaic - 240 280 ma 1 power consumption pc - 0.8 0.92 watt 1 differential impedance zm 90 100 110 ohm 2 led backlight : (without led driver) led driver input volatge (on system) vled 12 v 3 operating current per string i led 5 20 25 ma 4 the lp097x02 requires two power inputs. one is emp loyed to power the lcd electronics and to drive the tft array and liquid crystal. the second input whic h powers the led bl. ver. 0.1 23. apr. 2010 6 / 28 power consumption p bl 2.1 2.6 watt 5 life time 10,000 - - hrs 6 note) 1. the specified current and power consumption are under the vcc = 3.3v , 25 , fv = 60hz condition whereas mosaic pattern is displayed and fv is the f rame frequency. 2. this impedance value is needed to proper display and measured form lvds tx to the mating connector. 3. led input voltage must be input below than 12v to operate normally for led driver. 4. the typical operating current is for the typica l surface luminance (l wh ) in optical characteristics. 5. the led power consumption shown above does not i nclude power of external led driver circuit for typical current condition. 6. the life time is determined as the time at which brightness of lamp is 50% compare to that of initi al value at the typical lamp current. www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 3-2. interface connections this lcd employs two interface connections, a 30 pi n connector is used for the module electronics inte rface and the other connector is used for the integral ba cklight system. the electronics interface connector is a model 2047 4-030e-12 manufactured by i-pex. table 3. module connector pin configuration (cn1) pin symbol description notes 1 gnd ground [lvds receiver] [lvds receiver] [lvds receiver] [lvds receiver] siliconworks, sw0627b [connector] [connector] [connector] [connector] i-pex 20474-030eC1# [mating connector] [mating connector] [mating connector] [mating connector] i-pex 20472-030t-10 series or equivalent (micro-coax type) [connector pin arrangement] [connector pin arrangement] [connector pin arrangement] [connector pin arrangement] lcd front view 2 vcc power supply, 3.3v typ. 3 vcc power supply, 3.3v typ. 4 v eedid ddc 3.3v power 5 gsp gsp 6 clk eedid ddc clock 7 data eedid ddc data 8 r in 0- negative lvds differential data input 9 r in 0+ positive lvds differential data input 10 gnd ground 11 r in 1- negative lvds differential data input 30 1 ver. 0.1 23. apr. 2010 7 / 28 12 r in 1+ positive lvds differential data input 13 gnd ground 14 r in 2- negative lvds differential data input 15 r in 2+ positive lvds differential data input 16 gnd ground 17 clkin- negative lvds differential clock input 18 clkin+ positive lvds differential clock input 19 gnd ground 20 nc no connection 21 vdc led anode (positive) 22 vdc led anode (positive) 23 nc no connection 24 vdc1 led cathode (negative) 25 vdc2 led cathode (negative) 26 vdc3 led cathode (negative) 27 vdc4 led cathode (negative) 28 vdc5 led cathode (negative) 29 vdc6 led cathode (negative) 30 nc no connection www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display description symb ol min max unit notes lvds differential voltage |v id | 100 600 mv - lvds common mode voltage v cm 0.6 1.8 v - lvds input voltage range v in 0.3 2.1 v - 3-3-1. dc specification 3-3. lvds signal timing specifications ver. 0.1 23. apr. 2010 8 / 28 description symbol min max unit notes lvds clock to data skew margin t skew - 400 + 400 ps 85mhz > fclk 65mhz t skew - 600 + 600 ps 65mhz > fclk 25mhz lvds clock to clock skew margin (even to odd) t skew_eo - 1/7 + 1/7 t clk - maximum deviation of input clock frequency during ssc f dev - 3 % - maximum modulation frequency of input clock during ssc f mod - 200 khz - 3-3-2. ac specification www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display < clock skew margin between channel > f center f max f min f mod 1 f center * f dev freq. ver. 0.1 23. apr. 2010 9 / 28 < lvds data format > 3-3-3. data format -. lvds 1 port < spread spectrum > time g0 r5 r4 r3 r2 r1 r0 b1 b0 g5 g4 g3 g2 g1 de vsync hsync b5 b4 b3 b2 x b7 b6 g7 g6 r7 r6 r1 r0 g2 g1 b3 b2 r7 r6 g0 b1 de x current (nth ) cycle r5 r4 b0 g5 vsync hsync b7 b6 r3 r2 g4 g3 b5 b4 g7 g6 previous (n-1)th cycle next (n+1)th cycle rclk+ ra+/- rb+/- rc+/- rd+/- www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 3-4. signal timing specifications table 6. timing table this is the signal timing required at the input of the user connector. all of the interface signal ti ming should be satisfied with the following specifications and spe cifications of lvds tx/rx for its proper operation. item symbol min typ max unit note dclk frequency f clk 97 100.03 103 mhz hsync active thp 1024 1024 1024 tclk period t wh 1960 2084 2223 width-active t wha 240 320 400 vsync active t vp 768 768 768 thp period t wv 776 800 824 width-active t wva 3 10 17 data enable horizontal back porch t hbp 400 480 560 tclk horizontal front porch t hfp 180 260 320 vertical back porch t vbp 4 6 12 thp vertical front porch t vfp 1 16 32 ver. 0.1 23. apr. 2010 10 / 28 3-5. signal timing waveforms condition : vcc =3.3v low: 0.3vcc high: 0.7vcc data enable, hsync, vsync hsync data enable vsync data enable t wh t hp t hfp t hbp t vp t wv t vbp t vfp t wha t wva t clk 0.5 vcc dclk www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 3-6. color input data reference the brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color. t he table below provides a reference for color versus data input. table 7. color data reference color input color data red msb lsb green msb lsb blue msb lsb r 5 r 4 r 3 r 2 r 1 r 0 g 5 g 4 g 3 g 2 g 1 g 0 b 5 b 4 b 3 b 2 b 1 b 0 basic color black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 ver. 0.1 23. apr. 2010 11 / 28 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red red (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green green (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 ... green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue blue (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 3-7. power sequence t 6 interface signal, v i (lvds signal of transmitter) lamp power power supply for lcd vcc 90% 10% 10% 0v 90% t 1 t 2 t 5 valid data 0v off off lamp on t 7 t 3 t 4 ver. 0.1 23. apr. 2010 12 / 28 note) 1. valid data is data to meet 3-3. lvds signal tim ing specifications 2. please avoid floating state of interface signal at invalid period. 3. when the interface signal is invalid, be sure to pull down the power supply for lcd vcc to 0v. 4. lamp power must be turn on after power supply fo r lcd and interface signal are valid. parameter value units min. typ. max. t 1 0.5 - 10 (ms) t 2 0 - 50 (ms) t 3 200 - - (ms) t 4 200 - - (ms) t 5 0 - 50 (ms) t 6 0 - 10 (ms) t 7 400 - - (ms) table 8. power sequence table www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 4. optical specification fig. 1 optical characteristic measurement equipment and method table 9. optical characteristics optical characteristics are determined after the unit has b een on and stable for approximately 20 minutes in a dark environment at 25 c . the values specified are at an approximate distance 50cm fr om the lcd surface at a viewing angle of f and q equal to 0 . fig. 1 presents additional information concerning t he measurement equipment and method. ta=25 c, vcc=3.3v, f v =60hz, f clk = 100.03mhz, iled = 20ma lcd module optical stage(x,y) equipment 500mm 50mm parameter symbol condition min typ max units notes average luminance l 5 points 340 400 - cd/ O 2 ver. 0.1 23. apr. 2010 13 / 28 average luminance l ave 5 points (iled= 20ma) 340 400 - cd/ O 2 luminance variation d white 13 points - 1.4 1.6 % 3 c/r - center 1 point 500 600 - - 1 response time - - 30 50 ? 4 viewing angle horizontal x(left,right) 80 89 - ? 5 vertical yu(up) 80 89 - yd(down) 80 89 - color coordinates red rx 0.574 0.604 0.634 ry 0.321 0.351 0.381 green gx 0.291 0.321 0.351 gy 0.522 0.552 0.582 blue bx 0.122 0.152 0.182 by 0.103 0.133 0.163 white wx 0.283 0.313 0.343 wy 0.299 0.329 0.359 cross talk dsha - - - 4.0 % fig.5 gray scale - - gamma 2.2 6 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display note) 1. contrast ratio(cr) is defined mathematically as surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is the average of 5 point acro ss the lcd surface 50cm from the surface with all pixels displaying white. for more information see fig 1. l wh = average(l 1 ,l 2 , l 5 ) 3. the variation in surface luminance , the panel t otal variation ( d white ) is determined by measuring l n at each test position 1 through 13 and then defined as followed numerical formula. for more information see fig 2. maximum(l 1 ,l 2 , l 13 ) d white = minimum(l 1 ,l 2 , l 13 ) 4. response time is the time required for the displ ay to transition from white to black (rise time, tr r ) and from black to white(decay time, tr d ). for additional information see fig 3. 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined ver. 0.1 23. apr. 2010 14 / 28 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig 4. 6. gray scale specification * f v = 60hz gray level luminance [%] (typ) l0 0.12 l7 1.00 l15 4.30 l23 9.80 l31 19.2 l39 34.2 l47 53.5 l55 74.5 l63 100 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display fig. 3 response time the response time is defined as the following figur e and shall be measured by switching the input sign al for black and white. tr r tr d % fig. 2 luminance product specification lp097x02 liquid crystal display fig. 5 cross talk ver. 0.1 23. apr. 2010 16 / 28 5. mechanical characteristics the contents provide general mechanical characteristics f or the model lp097x02. in addition the figures in the next page are detailed mechanical drawing of the lcd. outline dimension horizontal 210.53 0.50mm (without bracket length) vertical 166.53 0.50mm (without bracket length) thickness 3.55mm(max.) pcb area : 5.82(max.) bezel area horizontal 201.40mm vertical 152.26mm active display area horizontal 196.608mm vertical 147.456mm weight 160g (max.) surface treatment hard coating(3h), glare treatment of the front polarizer (haze 0%) www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display product specification lp097x02 liquid crystal display product specification lp097x02 liquid crystal display 6. reliability environment test condition { result evaluation criteria } no. test item conditions 1 high temperature storage test ta= 60 c, 240h 2 low temperature storage test ta= -20 c, 240h 3 high temperature operation test ta= 50 c, 50%rh, 240h 4 low temperature operation test ta= 0 c, 240h 5 vibration test (non-operating) sine wave, 10 ~ 500 ~ 10hz, 1.5g, 0.37oct/min 3 axis, 1hour/axis 6 shock test (non-operating) half sine wave, 180g, 2m s one shock of each six faces(i.e. run 180g 6ms for all six faces) 7 altitude operati ng storage / shipment 0 ~ 10,000 feet (3,048m) 24hr 0 ~ 40,000 feet (12,192m) 24hr ver. 0.1 23. apr. 2010 19 / 28 { result evaluation criteria } there should be no change which might affect the pr actical display function when the display quality test is conducted under normal operating condition. www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 7. international standards 7-1. safety 7-2. emc a) ansi c63.4 methods of measurement of radio-noise emissi ons from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. america n national standards institute(ansi), 1992 b) c.i.s.p.r limits and methods of measurement of radio int erface characteristics of information technology equipment. international special commit tee on radio interference. c) en 55022 limits and methods of measurement of radio interface characteristics of information a) ul 60950-1:2003, first edition, underwriters lab oratories, inc., standard for safety of information technology equip ment. b) can/csa c22.2, no. 60950-1-03 1 st ed. april 1, 2003, canadian standards association, standard for safety of information technology equip ment. c) en 60950-1:2001, first edition, european committee for electrotechnical standardiza tion(cenelec) european standard for safety of information technol ogy equipment. ver. 0.1 23. apr. 2010 20 / 28 c) en 55022 limits and methods of measurement of radio interface characteristics of information technology equipment. european committee for elect rotechnical standardization.(cenelec), 1998 ( including a1: 2000 ) www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 8. packing 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m a,b,c : size(inch) d : year e : month f ~ m : serial no. note 1. year 2. month mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 nov month oct jun jul aug sep apr may dec mar feb jan ver. 0.1 23. apr. 2010 21 / 28 8-2. packing form b mark a 6 7 8 9 4 5 c 3 2 1 b) location of lot mark serial no. is printed on the label. the label is at tached to the backside of the lcd module. this is subject to change without prior notice. a) package quantity in one box : 40 pcs b) box size : 365mm 478mm 328mm www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1. mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneve n force (ex. twisted stress) is not applied to the module. and the case on which a module is mounted should have s ufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cove r case are not desirable because the former generates corrosive gas of attacking the polarizer at high t emperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glas s, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy c loth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with a bsorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is rec ommended for cleaning the adhesives used to attach front / rear polarizers . do not use acetone, toluene and alcohol because they cause ver. 0.1 23. apr. 2010 22 / 28 used to attach front / rear polarizers . do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their l ong time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lo wer temperature, it becomes longer.) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperature chang e. condensation makes damage to polarizer or electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppres sion to the electromagnetic interference shall be done by system manufacturers. grounding and shielding meth ods may be important to minimized the interference. www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display since a module is composed of electronic circuits, it is not s trong to electrostatic discharge. make certain that treatment persons are connected to ground through w rist band etc. and dont touch interface pin direct ly. 9-3. electrostatic discharge control strong light exposure causes degradation of polariz er and color filter. 9-4. precautions for strong light exposure 9-5. storage (1) when the protection film is peeled off, static electricity is generated between the film and polar izer. this should be peeled off slowly and carefully by p eople who are electrically grounded and with well 9-6. handling precautions for protection film when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunl ight or fluorescent light. keep the temperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that they be stored in the contai ner in which they were shipped. ver. 0.1 23. apr. 2010 23 / 28 this should be peeled off slowly and carefully by p eople who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) the protection film is attached to the polarize r with a small amount of glue. if some stress is ap plied to rub the protection film against the polarizer du ring the time you peel off the film, the glue is ap t to remain on the polarizer. please carefully peel off the protection film witho ut rubbing it against the polarizer. (3) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the polarizer af ter the protection film is peeled off. (4) you can remove the glue easily. when the glue r emains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cot ton waste or other soft material like chamois soaked with normal-hexane. www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display appendix a. enhanced extended display identificatio n data (eedid tm ) 1/3 byte# byte# (decimal) (hex) 0 00 header 0 0 0000 0000 1 01 header f f 1111 1111 2 02 header f f 1111 1111 3 03 header f f 1111 1111 header header header header 4 04 header f f 1111 1111 5 05 header f f 1111 1111 6 06 header f f 1111 1111 7 07 header 0 0 0000 0000 8 08 eisa manufacture code ( 3 character id ) 0 6 0000 0110 9 09 eisa manufacture code (compressed asc) 1 0 0001 0000 10 0a panel supplier reserved - product code = k48(0x 9cd3) d 3 1101 0011 11 0b ( hex. lsb first ) 9 c 1001 1100 12 0c lcd module serial no - preferred but optional ( "0" if not used) 0 0 0000 0000 v ender/ v ender/ v ender/ v ender/ 13 0d lcd module serial no - preferred but optional ( "0" if not used) 0 0 0000 0000 product id product id product id product id 14 0e lcd module serial no - preferred but optional ( "0" if not used) 0 0 0000 0000 15 0f lcd module serial no - preferred but optional ( "0" if not used) 0 0 0000 0000 16 10 week of manufacture 00 weeks 0 0 0000 0000 17 11 year of manufacture 2009 years 1 3 0001 0011 18 12 edid structure version # = 1 0 1 0000 0001 edid v ersion/ edid v ersion/ edid v ersion/ edid v ersion/ 19 13 edid revision # = 3 0 3 0000 0011 revision revision revision revision 20 14 video input definition = digital signal 8 0 1000 0000 21 15 max h image size (rounded cm) = 1 4 0001 0100 display display display display 22 16 max v image size (rounded cm) = 0 f 0000 1111 parameter parameter parameter parameter 23 17 display gamma = (gamma*100)-100 = example:(2.2*100) -100=120 7 8 0111 1000 field name and comments value (hex) value (binary) ver. 0.1 23. apr. 2010 24 / 28 23 17 display gamma = (gamma*100)-100 = example:(2.2*100) -100=120 7 8 0111 1000 24 18 feature support (no_dpms, no_active off/very lo w power, rgb color display, timing blk 1,no_ gtf) 0 a 0000 1010 25 19 red/green low bits (rxry/gxgy) 0 0 0000 0000 26 1a blue/white low bits (bxby/wxwy) 0 5 0000 0101 27 1b red x rx = 00 0 0 0000 0000 28 1c red y ry = 00 0 0 0000 0000 29 1d green x gx = 00 0 0 0000 0000 color color color color 30 1e green y gy = 00 0 0 0000 0000 characteristic characteristic characteristic characteristic 31 1f blue x bx = 00 0 0 0000 0000 32 20 blue y by = 00 0 0 0000 0000 33 21 white x wx = 0.313 5 0 0101 0000 34 22 white y wy = 0.329 5 4 0101 0100 35 23 established timing 1 (00h if not used) 0 0 0000 0000 es tablished es tablished es tablished es tablished 36 24 established timing 2 (00h if not used) 0 0 0000 0000 timings timings timings timings 37 25 manufacturer's timings (00h if not used) 0 0 0000 0000 38 26 sm pl_m p sm pl_m p sm pl_m p sm pl_m p a aa a 0 00 0 1010 0000 39 27 panel vendor id 0x97 9 7 1001 0111 40 28 low order bits of project id_auto-boot support(1)_l ow order 3 bits of device vendor id 6 9 0110 1001 41 29 high order bits of project id_lcd native color_blac k(1)_high order 3 bits of device vendor id 0 9 0000 1001 42 2a 0x00 0 0 0000 0000 43 2b 0x00 0 0 0000 0000 44 2c 0x00 0 0 0000 0000 standard standard standard standard 45 2d 0x00 0 0 0000 0000 timing id timing id timing id timing id 46 2e 0x00 0 0 0000 0000 47 2f 0x00 0 0 0000 0000 48 30 0x00 0 0 0000 0000 49 31 0x00 0 0 0000 0000 50 32 operating frequency setting (54mhz =0x36, 100mhz =0 x64) 6 4 0110 0100 51 33 b/l configuration(dy:0x, roe:1x, hs:2x)(tg:x0, nich ia:x1) 2 0 0010 0000 52 34 0x00 0 0 0000 0000 53 35 0x00 0 0 0000 0000 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display appendix a. enhanced extended display identificatio n data (eedid tm ) 2/3 byte# byte# (decimal) (hex) 54 36 pixel clock/10,000 (lsb) : 100mhz 1 3 0001 0011 55 37 pixel clock/10,000 (msb) 2 7 0010 0111 56 38 horizontal active (lower 8 bits) 1 024pixel 0 0 0000 00 00 57 39 horizontal blanking(thp-ha) (lower 8 bits) 1060pi xel 2 4 0010 0100 58 3a horizontal active / horizontal blanking(thp-ha) (upper 4:4bits) 4 4 0100 0100 59 3b vertical avtive 768line 0 0 0000 0000 60 3c vertical blanking (tvp-ha) (de blanking typ.for de only panels) 32line 2 0 0010 0000 61 3d vertical active : vertical blanking (tvp-ha) (upper 4:4bits) 3 0 0011 0000 timing timing timing timing 62 3e horizontal sync. offset (thfp) 260 pixel 0 4 0000 0100 descriptor descriptor descriptor descriptor 63 3f horizontal sync pulse width (hspw) 320pi xel 4 0 0100 0000 #1 #1#1 #1 64 40 vertical sync offset(tvfp) : sync width (vspw) 16line/10l ine 0 a 0000 1010 65 41 horizontal vertical sync offset/width (upper 2bits) 5 4 0101 0100 66 42 horizontal image size (mm) c 5 1100 0101 67 43 vertical image size (mm) 9 4 1001 0100 68 44 horizontal image size / vertical image size 0 0 0000 0000 69 45 horizontal border = 0 (zero for notebook lcd) 0 0 0000 0000 70 46 vertical border = 0 (zero for notebook lcd) 0 0 0000 0000 71 47 non-interlace, normal display, no stereo, digital s eparate ( vsync_neg, hsync_neg ) 1 8 0001 1000 72 48 flag 0 0 0000 0000 73 49 flag 0 0 0000 0000 74 4a flag 0 0 0000 0000 75 4b data type tag (descriptor defined by manufactu rer ) 0 1 0000 0001 76 4c flag 0 0 0000 0000 77 4d descriptor defined by manufacturer ( apple edid sig nature ) 0 6 0000 0110 field name and comments value (hex) value (binary) ver. 0.1 23. apr. 2010 25 / 28 77 4d descriptor defined by manufacturer ( apple edid sig nature ) 0 6 0000 0110 78 4e descriptor defined by manufacturer ( apple edid sig nature ) 1 0 0001 0000 79 4f descriptor defined by manufacturer ( link type ) 3 0 0011 0000 timing timing timing timing 80 50 descriptor defined by manufacturer ( pixel and link component format_6bit panel interface ) 0 0 0000 0000 description description description description 81 51 descriptor defined by manufacturer ( panel feature_ inverter na, no inverter ) 0 0 0000 0000 #2 #2#2 #2 82 52 descriptor defined by manufacturer 0 0 0000 0000 83 53 descriptor defined by manufacturer 0 0 0000 0000 84 54 descriptor defined by manufacturer 0 0 0000 0000 85 55 descriptor defined by manufacturer 0 0 0000 0000 86 56 descriptor defined by manufacturer 0 0 0000 0000 87 57 descriptor defined by manufacturer 0 0 0000 0000 88 58 (if<13 char--> 0ah, then terminate with asc co de 0ah,set remaining char = 20h) 0 a 0000 1010 89 59 (if<13 char--> 0ah, then terminate with asc co de 0ah,set remaining char = 20h) 2 0 0010 0000 90 5a flag 0 0 0000 0000 91 5b flag 0 0 0000 0000 92 5c flag 0 0 0000 0000 93 5d data type tag ( ascii string ) f e 1111 1110 94 5e flag 0 0 0000 0000 95 5f l 4 c 0100 1100 96 60 p 5 0 0101 0000 97 61 0 3 0 0011 0000 timing timing timing timing 98 62 9 3 9 0011 1001 description description description description 99 63 7 3 7 0011 0111 #3 #3#3 #3 100 64 x 5 8 0101 1000 101 65 0 3 0 0011 0000 102 66 2 3 2 0011 0010 103 67 - 2 d 0010 1101 104 68 s 5 3 0101 0011 105 69 l 4 c 0100 1100 106 6a a 4 1 0100 0001 107 6b 3 3 3 0011 0011 www.datasheet.co.kr datasheet pdf - http://www..net/ product specification lp097x02 liquid crystal display appendix a. enhanced extended display identificatio n data (eedid tm ) 3/3 byte# byte# (decimal) (hex) 108 6c flag 0 0 0000 0000 109 6d flag 0 0 0000 0000 110 6e flag 0 0 0000 0000 111 6f data type tag ( ascii string ) f e 1111 1110 112 70 flag 0 0 0000 0000 113 71 c 4 3 0100 0011 114 72 o 6 f 0110 1111 115 73 l 6 c 0110 1100 timing timing timing timing 116 74 o 6 f 0110 1111 description description description description 117 75 r 7 2 0111 0010 #4 #4#4 #4 118 76 space 2 0 0010 0000 119 77 l 4 c 0100 1100 120 78 c 4 3 0100 0011 121 79 d 4 4 0100 0100 122 7a lf 0 a 0000 1010 123 7b space 2 0 0010 0000 124 7c space 2 0 0010 0000 125 7d space 2 0 0010 0000 126 7e extension flag (# of optional 128 panel id ext ension block to follow, typ = 0) 0 0 0000 0000 extens ion flag extens ion flag extens ion flag extens ion flag 127 7f check sum (the 1-byte sum of all 128 bytes in this panel id block shall = 0) 6 66 6 b bb b 0110 1011 checks um checks um checks um checks um field name and comments value (hex) value (binary) ver. 0.1 23. apr. 2010 26 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/ |
Price & Availability of LP097X02-SLA3
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |