View B089AW01V3_2323462.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification au optronics corporation ( ) preliminary specifications ( v ) final specifications module model name note ( ) wsvga color tft-lcd with led backlight design b089aw01 v3 led backlight with driving circuit design customer date approved by date howard lee 11/05/2008 checked & approved by date prepared by wisdom che 11/05/2008 note: this specification is subject to change without notice. nbbu marketing division / au optronics corporation contents document version 1.0 1 of 34 www..net
product specification au optronics corporation 1. handling precautions............................. ................................................... ........................ 4 2. general description ............................ ................................................... ........................... 5 2.1 general specification.......................... ................................................... ................................................... ...... 5 2.2 optical characteristics ....................... ................................................... ................................................... ...... 6 3. functional block diagram ........................ ................................................... .................... 11 4. absolute maximum ratings........................ ................................................... ................................................... ......11 5. electrical characteristics ...................... ................................................... ........................ 13 5.1 tft lcd module.................................. ................................................... ................................................... .... 13 5.2 backlight unit ................................ ................................................... ................................................... .......... 15 6. signal characteristic ........................... ................................................... ......................... 16 6.1 pixel format image............................. ................................................... ................................................... ..... 16 6.2 the input data format........................... ................................................... ................................................... ... 17 6.3 signal description/pin assignment ............. ................................................... ............................................. 18 6.4 interface timing................................ ................................................... ................................................... ....... 21 6.5 power sequence................................. ................................................... ................................................... ..... 23 6.5.1 panel power sequence ........................ ................................................... ................................................... 23 7. connector description .......................... ................................................... ....................... 24 7.1 tft lcd module.................................. ................................................... ................................................... .... 24 8. 8. led driving specification .................... ................................................... ..................... 25 8.1 connector description.......................... ................................................... ................................................... .. 25 8.2 pin assignment................................. ................................................... ................................................... ....... 25 9. vibration and shock test ......................... ................................................... .................... 26 9.1 vibration test ................................. ................................................... ................................................... .......... 26 9.2 shock test spec: .............................. ................................................... ................................................... ....... 26 11. mechanical characteristics..................... ................................................... .................... 28 11.1 lcm outline dimension ......................... ................................................... .................................................. 28 11.2 screw hole depth and center position ......... ................................................... ......................................... 29 12. shipping and package............................ ................................................... .................... 30 12.1 shipping label format.......................... ................................................... ................................................... 30 12.2 carton package................................ ................................................... ................................................... ...... 31 12.3 shipping package of palletizing sequence ..... ................................................... ....................................... 31 13. appendix: edid description ...................... ................................................... ................. 32 document version 1.0 2 of 34 www..net
product specification au optronics corporation record of revision version and date page 0.1 2008/08/06 1.0 2008/10/29 1.0 2008/10/29 all 5 6 old description first edition for customer add glass thickness data response time [rising , falling] tbd rising 6ms typ, fa lling 2ms typ new description remark document version 1.0 3 of 34 www..net
product specification au optronics corporation 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interf ace connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideratio n that no bending/twisting forces are applied to the tft module from outside. otherwi se the tft module may be damaged. 12) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied exem ption. 13) disconnecting power supply before handling lcd modules, it can prevent electric shock, do not touch the electrode parts, cables, connecto rs and led circuit part of tft module that a led light bar build in as a light source of back light unit. it can prevent electrostic breakdown. document version 1.0 4 of 34 www..net
product specification au optronics corporation 2. general description b089aw01 v3 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and led backlight system. the scree n format is intended to support the wsvga (1024(h) x 600(v)) screen and 262k colors (rgb 6-bi ts data driver) with led backlight driving circuit. all input signals are lvds interface compa tible. b089aw01 v3 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification items screen diagonal active area pixels h x v pixel pitch pixel arrangement display mode white luminance note: i led is led current luminance uniformity contrast ratio response time nominal input voltage vdd power consumption weight physical size unit [mm] [mm] 226.06(w) 195.07(h) x 113.4(v) 1024x3(rgb) x 600 [mm] 0.1905 (h) x 0.189 (v) r.g.b. vertical stripe normally white [cd/m 2 ] 200 typ 170 min (note1) [ms] [volt] [watt] 1.25max.( 5 points) 1.6 max. (13 points) 300 typ 8 typ / 16 max +3.3 typ. 3.0 max. (include logic and black light power) w 129.85 129.55 - t 5.45 5.15 - electrical interface glass thickness [grams] 190 max. [mm]l max213.66 typical213.36 min- 1 channel lvds [mm] 0.5 document version 1.0 the following items are characteristics summary on the table at 25 condition: specifications 5 of 34 www..net
product specification au optronics corporation surface treatment support color temperature range operating storage (non-operating) rohs compliance glare 262k colors ( rgb 6-bit ) [ o c] o [ c] 0 to +50 -20 to +65 rohs compliance 2.2 optical characteristics item white luminance viewing angle unit [cd/m ] [degree] [degree] [degree] [degree] luminance uniformity luminance uniformity cr: contrast ratio cross talk response time % [msec] [msec] [msec] rising falling rising + falling red x red y chromaticity of color coordinates (cie 1931) green x green y blue x blue y white x white y - - - 0.535 0.304 0.29 0.529 0.092 0.048 0.263 0.279 6 2 8 0.585 0.354 0.34 0.579 0.142 0.098 0.313 0.329 2 conditions 5 point horizontal (right) cr = 10(left) vertical (upper) cr = 10 (lower) 5 points 13 points document version 1.0 the optical characteristics are measured under stab le conditions at 25 (room temperature) : min. 170 - - - - - - 200 typ. 200 45 45 15 35 - - 300 max. - - - - - 1.25 1.6 - 4 12 4 16 0.635 0.404 0.39 0.629 0.192 0.148 0.363 0.379 note 1,3 3,8 1,4,5 2,4,5 5,7 4,6 4,7 4,8 6 of 34 www..net
product specification au optronics corporation note 1 : 5 points position (ref: active area) w w /4 w /4 w /4 w /4 h /4 1 h /4 h h /4 2 3 4 h /4 5 note 2. 13 points position (ref: active area) w w /4 10 10 h /4 w /4 w /4 w /4 10 1 4 2 5 3 h /4 h h /4 6 7 8 9 h /4 10 10 12 13 11 note 3: the luminance uniformity of 13 points is define d by dividing the maximum luminance values by the m inimum test point luminance w5 = maximum brightness of five points minimum brightness of five points maximum brightness of thirteen points minimum brightness of thirteen points document version 1.0 w 13 = 7 of 34 www..net
product specification au optronics corporation note 4: measurement method the lcd module should be stabilized at given tempera ture for 30 minutes to avoid abrupt temperature cha nge during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room. photo detector (bm-5a,bm-7 or equivalent) lcd panel center of the screen document version 1.0 note 5 definition of contrast ratio: contrast ratio is calculated with the following fo rmula. contrast ratio (cr)= brightness on the white state brightness on the black state 50 cm tft-lcd module 8 of 34 field=2 www..net
product specification au optronics corporation ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 7: definition of response time: the output signals of bm-7 or equivalent are measure d when the input signals are changed from black t o white (falling time) and from white to black ( rising time), respectively. the response time inter val between the 10% and 90% of amplitudes. refer to figure as below. document version 1.0 note 6 definition of cross talk (ct) "white" 100% 90% signal(relati ve value) "black" "white" 10% 0% tr tf 9 of 34 www..net
product specification au optronics corporation note8. definition of viewing angle 170 vertical range (off-normal viewing angles). th e 170 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the scree n rotated about its center to develop the desired m easurement viewing angle. document version 1.0 viewing angle is the measurement of contrast ratio 10, at the screen center, over a 170 horizontal an d 10 of 34 www..net
product specification au optronics corporation 3. functional block diagram the following diagram shows the functional block of the 8.9 inches wide color tft/lcd 40 pin (one ch/connector module: tcon lvds receiver panel controller tft-lcd tft-lcd 1280*(3)*800 1024*(3)*600 pixels pixels c onnector co nne cto connector r dc power dc/dc converter source driver ic control signal gamma correction generation circuit gamma1~14 led power led driver boost and current balance circuit led light bar 6 strings, 7pcs/string document version 1.0 11 of 34 gagate d river ic lvds www..net
product specification au optronics corporation 4.1 absolute ratings of tft lcd module item logic/lcd drive voltage symbol vin min -0.3 max +4.0 unit [volt] conditions note 1,2 4.2 absolute ratings of environment item operating temperature operation humidity storage temperature storage humidity symbol top hop tst hst min 0 10 -20 10 max +50 90 +60 90 unit [ c] [%rh] [ c] [%rh] o o conditions note 4 note 4 note 4 note 4 note 2: permanent damage to the device may occur if exc eed maximum values note 3: led specification refer to section 5.2 note 4: for quality performance, please refer to au o iis (incoming inspection standard). twb=39c operating range document version 1.0 note 1: at ta (25 ) storage range 12 of 34 www..net
product specification au optronics corporation 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble vdd pdd idd irush vddrp parameter logic/lcd drive voltage vdd power idd current inrush current allowable logic/lcd drive ripple voltage min 3.0 - - - - typ 3.3 0.86 260 650 - max 3.6 1 280 -- 100 unit s [volt] [watt note 1/2 ] [ma] note 1/2 [ma] note 3 [mv] p-p note note 3 g d1d2d5d6 c3 2 +12.0v sw1 sw mag-spst 1 vr1 47k 0.01uf/25v c2 1uf/25v s document version 1.0 note 2 typical measurement condition: mosaic pattern measure condition +5.0v d6 d5 d2 d1 r1 47k q3 ao6402 f1 s vcc (high to low) control signal r2 g 1k 0v 470us note 1 : maximum measurement condition black pattern (lcd module input) c1 1uf/16v q3 ao6402 90% 3.3v 10% vin rising time 13 of 34 www..net
product specification au optronics corporation 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of sn75lvds82dgg (texas instruments) in detail. signal electrical characteristics are as follows; parameter vth condition differential input high threshold (vcm=+1.2v) differential input low threshold (vcm=+1.2v) min max 100 unit [mv] - vtl -100 - [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform v t h vcm vss document version 1.0 14 of 34 www..net
product specification au optronics corporation 5.2 backlight unit parameter led circuit power supply led circuit input current led power consumption led pwm frequency symbol v led i led p led l freq 100 min 4.5 typ 5 350 1.75 200 max 5.5 460 2.1 20k units [volt] [ma ] [watt] hz (ta=25 ) i f =20 ma note 2 condition (ta=25 ) (ta=25 ) (ta=25 ) note 1 led life-time n/a 10,000 - - hour duty ratio --- 15 100 % note 1: calculator value for reference ifvf =p note 2: the led life-time define as the estimated time to 50% degradation of initial luminous. note 3: the led driving condition is defined for led mod ule (24 led) note 4: define led lifetime: brightness is decreased to 50% of the initial value. document version 1.0 15 of 34 www..net
product specification au optronics corporation 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. document version 1.0 16 of 34 www..net
product specification au optronics corporation 6.2 the input data format signal name r5 r4 r3 r2 r1 r0 description red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data data clock green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin de display timing vs hs vertical sync horizontal sync the typical frequency is 54.2mhz.the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. this signal is strobed at the falling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. the signal is synchronized to rxclkin . the signal is synchronized to rxclkin . note: output signals from any system shall be low or hig h-impedance state when vdd is off. document version 1.0 17 of 34 www..net
product specification au optronics corporation 6.3 signal description/pin assignment document version 1.0 18 of 34 www..net
product specification au optronics corporation lvds is a differential signal technology for lcd int erface and high speed data transfer device. note 1: the pwm pin should not connect to ground, it should pull-high if not adjust brightness. 40 nc connector: ipex 20347-340e-12 1 gnd stm msak24024p40 document version 1.0 19 of 34 www..net
product specification au optronics corporation note1: start from right side note2: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input signal input lvds receiver pin no. 8 rxin0 - r 9 rxin0+ 11 rxin1 - r 12 rxin1+ 14 rxin2 - r 15 rxin2+ 17 rxclkin - r 18 rxclk in+ document version 1.0 20 of 34 www..net
product specification au optronics corporation 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1024 x 600 /60hz manufacturing guide line timing. parameter frame rate clock frequency vertical section period active blanking horizontal section period active blanking symbol - 1/ t clock t v t vd t vb t h t hd t hb min. - -- 603 600 3 1303 1024 22 typ. 60 54.2 625 600 25 1344 1024 320 max. - 75 650 600 50 1534 1024 510 t clock t line unit hz mhz note : de mode only document version 1.0 21 of 34 www..net
product specification au optronics corporation 6.4.2 timing diagram t clock input timing definition ( de mode) dotclk input data invaild data pixel 1 pixel 2 pixel 3 pixel n -1 pixel n invaild data pixel 1 de t hb t h t hd de t vb t vd t v document version 1.0 22 of 34 www..net
product specification au optronics corporation 6.5 power sequence 6.5.1 panel power sequence vdd power and led on/off sequence is as follows. in terface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. . power sequence timing parameter t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 min. 0.5 30 200 10 10 0 10 100 0 - 1000 value typ. - 40 - - - - - - 16 - - max. 10 50 - - - - - - 50 10 - unit [ms] [ms] [ms] [ms] [ms] [ms] [ms] [ms] [ms] [ms] [ms] document version 1.0 23 of 34 www..net
product specification au optronics corporation 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation manufacturer type / part number mating housing/part number for signal connector ipex, stm o r compatible ipex20347-340e-12, stmmsak24024p40 or compatible ipex 20345-340e-12 or compatible document version 1.0 24 of 34 www..net
product specification au optronics corporation 8. 8. led driving specification 8.1 connector description it is a intergrative interface and comibe into lvds connector. the type and mating refer to section 7. 8.2 pin assignment document version 1.0 25 of 34 www..net
product specification au optronics corporation 9. vibration and shock test 9.1 vibration test test spec: test method: acceleration: frequency: sweep: non -operation 1.5 g 10 - 500hz random 30 minutes each axis (x, y, z) 9.2 shock test spec: test spec: test method: acceleration: active time: pulse: non -operation 220 g , half sine wave 2 ms x,y,z .one time for each side document version 1.0 26 of 34 www..net
product specification au optronics corporation 10. reliability items temperature humidity bias high temperature operation low temperature operation high temperature storage low temperature storage thermal shock test esd required condition ta= 40 , 90%rh, 300h ta= 50 , dry, 300h ta= 0 , 300h ta= 60 , 35%rh, 300h ta= -20 , 50%rh, 250h ta=-20 to 60 , duration at 30 min, 100 cycles contact : 8 kv air : 15 kv note 1 note note1: according to en 61000-4-2 , esd class b: some perfor mance degradation allowed. no data lost . self-recoverable. no hardware failures. remark: mtbf (excluding the led): 30,000 hours with a confid ence level 90% document version 1.0 27 of 34 www..net
product specification au optronics corporation 11. mechanical characteristics 11.1 lcm outline dimension note: in order to avoid ic damage, it is not allowed to have any component overlapping on those areas. document version 1.0 28 of 34 www..net
product specification au optronics corporation 11.2 screw hole depth and center position screw hole minimum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 2. 95 0.1mm (see drawing) suggestions: customers screw maximum length = 2.0 mm (see drawing) screw torque: maximum2.5 kgf-cm document version 1.0 29 of 34 www..net
product specification au optronics corporation 12. shipping and package 12.1 shipping label format * h/w code control table : ic combination source gate source gate novatek oaxxg novatek radium 1axxg radium 1a oa control code h/w document version 1.0 30 of 34 www..net
product specification au optronics corporation 12.2 carton package 12.3 shipping package of palletizing sequence document version 1.0 31 of 34 www..net
product specification au optronics corporation 13. appendix: edid description b089aw01 v3 edid code address hex 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e document version 1.0 function header value hex 00 ff ff ff ff ff ff 00 value bin 00000000 11111111 11111111 11111111 11111111 11111111 11111111 00000000 00000110 10101111 11000010 00010011 00000000 00000000 00000000 00000000 00000001 00010010 00000001 00000011 10000000 00010100 00001011 01111000 00001010 11100001 01000101 10010101 01011010 01010111 10010100 00100100 00011001 01010000 01010100 00000000 00000000 00000000 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 00000001 value dec 0 255 255 255 255 255 255 0 6 175 194 19 0 0 0 0 1 18 1 3 128 20 11 120 10 225 69 149 90 87 148 36 25 80 84 0 0 0 1 1 1 1 1 1 1 1 1 note eisa manuf. code lsb compressed ascii 06 af c2 13 00 00 00 00 week of manufacture year of manufacture edid structure ver. edid revision # video input def. (digital i/p, non-tmds, crgb) max h image size (rounded to cm) max v image size (rounded to cm) display gamma (=(gamma*100)-100) feature support (no dpms, active off, rgb, tmg blk#1) red/green low bits (lower 2:2:2:2 bits) blue/white low bits (lower 2:2:2:2 bits) red x (upper 8 bits) red y/ higher 8 bits green x green y blue x blue y white x white y established timing 1 established timing 2 established timing 3 standard timing #1 standard timing #2 standard timing #3 standard timing #4 standard timing #5 tsrif bsl ,xeh edoc tcudorp 32-bit ser # 01 12 01 03 80 14 0b 78 0a e1 45 95 5a 57 94 24 19 50 54 00 00 00 01 01 01 01 01 01 01 01 01 32 of 34 www..net
product specification au optronics corporation 2f 30 31 32 33 34 35 36 37 38 39 3a 3b 3c 3d 3e 3f 40 41 42 43 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f 60 61 document version 1.0 01 standard timing #6 standard timing #7 standard timing #8 01 01 01 01 01 01 7c 15 00 ae 41 58 1e 20 18 88 31 00 c3 71 00 00 00 18 00 00 00 0f 00 00 00 00 00 00 00 00 00 00 00 00 00 20 detailed timing/monitor descriptor #3 00 00 00 fe 00 manufacture manufacture manufacture 41 55 4f 00000001 00000001 00000001 00000001 00000001 00000001 00000001 01111100 00010101 00000000 10101110 01000001 01011000 00011110 00100000 00011000 10001000 00110001 00000000 11000011 01110001 00000000 00000000 00000000 00011000 00000000 00000000 00000000 00001111 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 00000000 00000000 00000000 11111110 00000000 01000001 01010101 01001111 1 1 1 1 1 1 1 124 21 0 174 65 88 30 32 24 136 49 0 195 113 0 0 0 24 0 0 0 15 0 0 0 0 0 0 0 0 0 0 0 0 0 32 0 0 0 254 0 65 85 79 a u o pixel clock/10000 lsb pixel clock/10000 usb horz active lower 8bits horz blanking lower 8bits horzact:horzblnk upper 4:4 bits vertical active lower 8bits vertical blanking lower 8bits vert act : vertical blanking (upper 4:4 bit) horzsync. offset horzsync.width vertsync.offset : vertsync.width horz&vert sync offset/width u p p e r 2 b i t s horizontal image size l o w e r 8 b i t s vertical image size l o w e r 8 b i t s horizontal & vertical image size ( u p p e r 4 : 4 b i t s ) horizontal border (zero for internal lcd) vertical border (zero for internal lcd) signal (non-intr, norm, no stero, sep sync, neg pol) detailed timing/monitor descriptor #2 33 of 34 www..net
product specification au optronics corporation 62 63 64 65 66 67 68 69 6a 6b 6c 6d 6e 6f 70 71 72 73 74 75 76 77 78 79 7a 7b 7c 7d 7e 7f extension flag checksum manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n manufacture p/n detailed timing/monitor descriptor #4 0a 20 20 20 20 20 20 20 20 20 00 00 00 fe 00 42 30 38 39 41 57 30 31 20 56 33 20 0a 00 37 00001010 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00100000 00000000 00000000 00000000 11111110 00000000 01000010 00110000 00111000 00111001 01000001 01010111 00110000 00110001 00100000 01010110 00110011 00100000 00001010 00000000 00110111 10 32 32 32 32 32 32 32 32 32 0 0 0 254 0 66 48 56 57 65 87 48 49 32 86 51 32 10 0 55 v 3 b 0 8 9 a w 0 1 document version 1.0 34 of 34 www..net

▲Up To Search▲

Price & Availability of B089AW01V3

	To Download B089AW01V3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .