l3urf9q53s/tr1 doc. no : qw0905-l3urf9q53s/tr1 rev. : a date : 29 - sep. - 2009 data sheet ligitek electronics co.,ltd. property of ligitek only plcc type red led lead-free parts pb l dcc
1.aonde red 2.aonde red 3.aonde red 4.cathode red 5.cathode red 6.cathode red note : 1.all dimension are in millimeter tolerance is ? 0.2mm unless otherwise noted. 2.specifications are subject to change without notice. 4.0 ? 0.2 note : the tolerances unless mentioned is ? 0.1mm,angle ? 0.5. unit=mm. 5.2 1.75 8.0? 0.2 5.5 ? 0.2 carrier type dimensions 5.6 12.0 ? 0.3 2.15 2.0 1.5 0.3 urfs urfs urfs 4 3 5.0 0.8 1.95 2 2.5 1.0 1.0 3 1 5.0 5.4 pin no.1 2 5 1 6 package dimensions part no. l3urf9q53s/tr1 1.0 0.7 5 4 6 1.0 1.0 0.7 ligitek electronics co.,ltd. property of ligitek only page 1/7
r 13.0 ? 0.5 330 ? 1.5 quantity/reel 4000 devices part no. l3urf9q53s/tr1 description 12.0mm tape,13"reel 17.5 ? 1.0 13.5 ? 1.0 6.0 ? 1.0 reel dimensions ligitek electronics co.,ltd. property of ligitek only page 2/7 part no. l3urf9q53s/tr1
t opr operating temperature -40 ~ +85 j note : 1.the forward voltage data did not including ? 0.1v testing tolerance. 2. the luminous intensity data did not including ? 15% testing tolerance. static electricity or power surge will damage the led. use of a c onductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. tstg typical electrical & optical characteristics (ta=25 j ) * storage temperature dominant wave length f dnm -40 ~ +100 j page 3/7 esd symbol i fp pd absolute maximum ratings at ta=25 j forward current electrostatic discharge( * ) reverse current @5v peak forward current duty 1/10@10khz power dissipation parameter i f ma 50 2000 ir 10 v g a 120 90 mw ma ratings urf(s) unit ligitek electronics co.,ltd. property of ligitek only part no. l3urf9q53s/tr1 120 500 320 1.7 2.6 20 625 water clear l3urf9q53s/tr1 lens emitted material part no color forward voltage @20ma(v) spectral halfwidth ??f nm luminous intensity @20ma(mcd) viewing angle 2 c 1/2 (deg) max. min. min. typ. algainp red
fig.3 forward voltage vs. temperature fig.5 relative intensity vs. wavelength ambient temperature( j ) relative intensity@20ma wavelength (nm) forward voltage@20ma normalize @25 j fig.4 luminous intensity vs. temperature ambient temperature( j ) luminous intensity@20ma normalize @25 j typical electro-optical characteristics curve forward voltage(v) fig.1 forward current vs. forward voltage forward current(ma) forward current(ma) luminous intensity normalize @20ma ligitek electronics co.,ltd. property of ligitek only 0 0 50 100 150 050100150 0.0 1.0 2.0 3.0 -40 -20 0 20 40 60 0.5 1.0 1.5 2.0 80 100 0.94 -20 -40 40 20 080100 60 0.8 0.0 0.2 0.4 0.6 1.0 1.2 urfs chip page 4/7 fig.2 luminous intensity vs. forward current 5.0 4.0 6.0 2.5 3.0 0.96 0.98 1.00 1.02 1.04 1.06 0 550 600 650 700 0.5 1.0 part no. l3urf9q53s/tr1
3. lead reflow solder note: 1.wave solder and reflow soldering should not be made more than one time. 2.you can just only select one of the soldering conditions as above. 120 sec.max. above 220xc 60 sec.max. preheat 180~200xc 1~5xc/sec 240 temp. ( j ) 150 4. pb-free reflow solder 120 60 ~ 120 sec 5sec 1~5xc/sec 260xc max. 10sec.max time cooling -5 j /sec rising +5 j /sec preheat page 5/7 1. hand solder basic spec is ?? 280 j 3 sec one time only. recommended soldering conditions 120 ~ 150 j 2. wave solder 120 ~ 180 sec preheat 245 ? 5 j within 5 sec soldering heat max. 260 j ligitek electronics co.,ltd. property of ligitek only part no. l3urf9q53s/tr1
drive method: led is a current operated device, and therefore, require r some kind of current limiting incorporated into the driver circuit. this current limiting typically takes the form of a current limiting resistor placed in series with the led. consider worst case voltage variations than could occur across the current limiting resistor. the forwrd current should not be allowed to c hange by more than 40 % of its desired value. (a) recommended circuit. (b) the difference of brightness between led could be f ound due to the vf-if characteristics of led. cleaning: use alcohol-based cleaning solvents such as isopropyl alc ohol to clean the led. esd(electrostatic discharge): static electricity or power surge will damage the led. use of a c onductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. led circuit model a led circuit model b ligitek electronics co.,ltd. property of ligitek only precautions for use: storage time: 1.the operation of temperatures and rh are : 5 j ~35 j ,rh<60%. 2.once the package is opened, the products s hould be used within a week. otherwise, they should be kept in a damp proof box with descanting agent. considering the tape life, we suggest our customers to use our pr oducts within a year(from production date). 3.if opened more than one week in an atmos phere 5 j ~ 35 j ,rh<60%, they should be treated at 60 j? 5 j fo r 15hrs. page 6/7 part no. l3urf9q53s/tr1
mil-std-202f:103b jis c 7021: b-11 high temperature high humidity storage test 1.ir-reflow in-board, 2 times 2.ta=65 j? 5 j 3.rh=90 %~95% 4.t=1000hrs ? 2hrs ramp-up rate(183 j to peak) +3 j second max temp. maintain at 125( ? 25) j 120 seconds max temp. maintain above 183 j 60-150 seconds peak temperature range 235 j +5-0 j time within 5 j of actual peak temperature(tp) 10-30 seconds ramp-down rate +6 j /second max environmental test solderability test temperature cycling 1.105 j ~ 25 j ~ 55 j ~ 25 j 30mins 5mins 30mins 5mins 2.10 cyeles 1.ir-reflow in-board,2 times 2.ta=105 j? 5 j & -40 j? 5 j (10min) (10min) 3.total 10 cycles solderability test 1.t.sol=235 j? 5 j 2.immersion time 2 ? 0.5sec 3.immersion rate 25 ? 2.5mm/sec 4.immersion rate 25 ? 2.5mm/sec 5.coverage ? 95% of the dipped surface thermal shock test mil-std-750d:2031.2 j-std-020 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1010 jis c 7021: a-4 mil-std-202f: 208d mil-std-750d: 2026 mil-std-883d: 2003 iec 68 part 2-20 jis c 7021: a-2 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1011 1.ta=under room temperature as per data sheet maximum rating. 2.if=20ma 3.t=1000 hrs (-24hrs, + 72hrs) endurance test low temperature storage test 1.ta=-40 j? 5 j 2.t=1000 hrs (-24hrs, + 72hrs) high temperature storage test 1.ta=105 j? 5 j 2.t=1000 hrs (-24hrs, + 72hrs) operating life test classification test item test condition reliability test: jis c 7021: b-12 mil-std-883d:1008 jis c 7021: b-10 mil-std-750d: 1026 mil-std-883d: 1005 jis c 7021: b-1 reference standard ligitek electronics co.,ltd. property of ligitek only page 7/7 part no. l3urf9q53s/tr1
|
