![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www..com SIDE VIEW IRMS6453 Preliminary 4 Mb/s Infrared Data Transceiver Dimensions in inches Absolute Maximum Ratings, TA=25C (except where noted) Supply Voltage Range, all states, VCC................................ -0.5 to +5.5 V Storage Temperature, TSTG.................................................. -25 to +85C Ambient Temperature, operating, TA ................................... -25 to +75C Lead Solder Temperature, .................................................... 240C<10 s IC Junction Temperature, TJ ........................................................... 125C Average IR LED Current, DC, ILED ................................................100 mA Repetitive Pulsed IR LED Current, <90 s, ton <25%, ILED(RP) ......................................................710 mA Transmit Data Input Voltage, VTxD ..............................-0.5 to VCC + 0.5 V Receive Data Output Voltage, VRxD ............................-0.5 to VCC + 0.5 V Pin Number 1 2 3 4 5 6 7 8 Symbol LEDA LEDC TxD RxD SD/ Mode VCC NC GND Description LED Anode LED Cathode Transmit Data Receive Data Shutdown/ Mode Select Positive Supply (Power) No Connect* Ground Features * IrDA, HP-SIR, Local Talk and Sharp ASK * Ultracompact package: * H 4.0 mm x D 4.8 mm x L 9.8 mm * Data rates from 9600 bit/s to 4 Mbit/s * Supply voltage 2.7 V to 5.25 V * Power Shutdown mode (<100 nA) * Low power consumption - 1.7 mA (typ) @ 2.7 V - 3.2 mA (typ) @ 5.0 V * Zero external resistors required Description Responding to the volumetric constraints of today's ultra-compact and power conscious portable products, Infineon has developed the next generation in infrared wireless communication transceivers. The transceiver has been designed to support up to 4 Mbit/s IrDA, HP-SIR, Local Talk and Sharp ASK modes. The device combines an LED, photodiode, LED driver and a fully differential receiver into a single integrated package. * Pin 7 internally grounded 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 1 Table 1. Input/Output Functional Description Symbol RxD I/O Type Output Polarity Active Low Function This output indicates received serial data. It is a push-pull CMOS driver capable of driving a standard CMOS or TTL load. No external pull-up or pull-down resistor is required. This output may switch indeterminately when the module is transmitting. This output pin is in tri-state mode when the module is in shutdown mode and during digital serial programming operations. RxD is high at initializaton. This CMOS input is used to transmit serial data when SD/ Mode is low. An on-chip protection circuit disables the LED driver if the TxDpin is asserted for longer than 60 s. When used in conjunction with the SD/ Mode pin. TxD is low at initializaton. Assertion of this pin high for a period of time exceeding 400 s places the module into shutdown mode. On the falling edge of this signal, the state of the TxDpin is sampled and used to set receiver low bandwidth (TxD= Low) or high bandwidth (TxD= High) mode. See Figures 7 and 8 for timings. SD is low at initializaton Connect to positive power supply (2.7 V to 5.25 V). Placement of a 1.0 F to 10.0 F decoupling ceramic capacitor as close as possible to the V CC pin is recommended. Connect to power supply ground. A solid ground plane is recommended. This pin could be connected to ground. This pin can be connected directly to VCC. No series resistor is required. LED cathode. Leave this pin unconnected. This pin may be monitored to determine the state of the LED. TxD Input Active High Active High SD/ Mode Input VCC GND NC LEDA LEDC Positive Supply Ground (Power) No Connect Input Output - Figure 1. Block Diagram VCC Figure 2. Minimum Infineon Low-Power Integrated Infrared Transceiver Circuit Diagram VCC C1 = 1 F to 10 F Amp Comp Driver RxD VCC IR Controller LEDA IRTX GPO VCC LEDA LEDC NC TxD IRMS6453 IRMS6452 SD/ Mode RxD SD/ Mode TxD Mode & Power Control Driver LEDC IRRX GND GND Table 2. Recommended Operating Conditions Symbol VCC TA Parameter Supply Voltage Ambient Operating Temperature Parameter Supply Current; Listening Supply Current; Receiving Supply Current; Shutdown Min 2.7 -25 Typical Max 5.25 75 Unit V C Conditions Table 3. DC Electrical Characteristics Symbol ICC ICC ISD Min 2.0 Typical 3.2 3.8 50 Max 4.5 15 100 Unit mA mA nA Conditions Typical value obtained at Vcc=5 V Interface and optical input power dependent VSD=VCC Table 4. Receiver DC Electrical Characteristics Symbol VOL IOL VOH IOH Parameter RxD Output Low Voltage Static Sink Current on RxD RxD Output High Voltage Static Source Current on RxD Vcc-0.5 2.4 Min Typical Max 0.5 2.4 Unit V mA V mA 2.2K load. 2.2K load. Conditions 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 2 IRMS6453 Symbol RL CL Parameter RxD Rosistive Load RxD Capacitive Load Min 2.2 Typical Max 50 Unit k pF Conditions Table 5. Transmitter DC Electrical Characteristics Symbol VIL VIH Ci Parameter TxD Input Voltage Low TxD Input Voltage High Input Capacitance 2.4 5 Min Typical Max 0.8 Unit V V pF Conditions Table 6. SD/Mode DC Electrical Characteristics Symbol VIL VIH Ci Parameter SD/ Mode Input Voltage Low SD/ Mode Input Voltage High Input Capacitance 2.4 5 Min Typical Max 0.8 Unit V V pF Conditions Table 7. Optical Characteristics Symbol Emin Emin Emin tr,tf txpw txpw txpw Ie aA p Parameter Minimum Detection Irradiance 9.6-115.2 kbit/s, SIR Minimum Detection Irradiance 1.152Mbit/s, MIR Minimum Detection Irradiance 4 Mbit/s, FIR LED Optical Rise/Fall Time SIR Optical Pulse Width MIR Optical Pulse Width FIR Optical Pulse Width Output Radiant Intensity Output Radiant Half Intensity Angle Peak Wavelength Optical Overshoot 1.41 147 115 110 15 850 870 900 25 200 Min Typical 3.7 4 7.9 9 40 22.13 261 140 400 Max 4 Unit W/ cm2 W/ cm2 W/ cm2 ns s ns ns mW/sr nm % TxD Input Pulse Width = 3/16 duty cycle TxD Input Pulse Width = 217ns TxD Input Pulse Width = 125ns TxD=High, SD/Mode=Low, VCC=3.3 V, = 15, TA=25C, TX@2MHz and 25% Conditions 9.6 kbit/s to 115.2 kbit/s 1.152 Mbit/s 4 Mbit/s Table 8. AC Electrical Characteristics Symbol tr tf tSU,tH tw tw tw tw tL tRxDEN tLEDP ILED ILED Parameter RxD Rise Time RxD Fall Time TxDSetup and Hold to SD/ Mode Falling Edge RxD Pulse Width (SIR) RxD Pulse Width (4Mbit/s, single pulse) RxD Pulse Width (4Mbit/s, double pulse) Receiver Latency RxD Valid After Shutdown LED Protection Time-out Peak Transmit Current Average Transmit Current 10 5 10 1.0 80 210 2.1 600 165 290 100 200 100 710 150 Min Typical Max 60 50 Unit ns ns ns s ns ns ns s s s mA mA 25% duty cycle 25% duty cycle IRMS6453 3 Conditions RL=2.2 K, CL=50 pF RL=2.2 K, CL=50 pF RxD Pulse Width (1.152Mbit/s) 100 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) Figure 3. Timing Diagrams Latency Timing V IH RxD Valid after Shutdown V IH TxD 50% V IL tL V OH SD/ Mode 50% V IL t RXEN 50% V OL VOH 50% VOL RxD RxD LED Protection Timing V IH RxD Timing 1.2 and 4 Mbit/s Mode tW TxD 50% V IL t LED P VOH 50% V OL RxD LEDC 50% RxD Timing, SIR mode. The output may be indeterminate in the shaded area. Spurious transitions may occur. tW ( m i n ) tW ( m a x ) RxD Rise and Fall Timing Measurements tP H L tP L H VO H 90% VO H RxD 50% 50% VO L RxD 10% V OL Figure 4. Bandwidth Programming Setting the Receiver to High BW Mode (FIR) V IH Setting the Receiver to Low BW Mode (SIR & MIR) V IH SD/ Mode 50% V IL SD/ Mode 50% V IL tSU TxD (Setting high bandwidth mode) tH V IH 50% V IL tSU tH 50% TxD (Setting low bandwidth mode) 50% 50% V IL The transceiver powers on with the receiver in low bandwidth mode. To enable high bandwidth mode, apply timings as shown in the figure 7, to the SD/ Mode and the TxD inputs. Note that the internal LED driver is disabled when SD/ Mode is active and is not enabled until the next rising edge of TxD. This ensures that the LED will not be active during bandwidth adjustment. It is recommended that the SD/ Mode pin be connected to GND if bandwidth adjustment and shutdown mode are not used. Setting the Receiver to High Bandwidth Mode (see Figure 4) 1. Set the SD/ Mode input to 'logic high'. 2. Set the TxD input to 'logic high'. Wait tsu 10 ns. 3. Set the SD/ Mode to 'logic low'. (This high-to-low transition latches the state of TxD, which determines the receiver bandwidth.) 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 4 4. After waiting th 10 ns, set the TxDinput to 'logic low'. The receiver is in high bandwidth mode within 200 s of the SD/ Mode rising edge or 10 ns after the SD/ Mode falling edge, whichever occurs later. Setting the Receiver to Low Bandwidth Mode (see Figure 4) 1. Set the SD/ Mode input to 'logic high'. 2. Ensure that the TxD input is at 'logic low'. Wait tsu 10 ns. 3. Set the SD/ Mode to 'logic low'. (This high-to-low transition latches the state of TxD, which determines the receiver bandwidth.) 4. Ensure that the TxD input remains low for th 10 ns. The receiver is in low bandwidth mode within 200 s of the SD/ Mode rising edge or 10 ns after the SD/ Mode falling edge, whichever occurs later. IRMS6453 Figure 5. Infrared Reflow Soldering Profile 300 Maximum 240(+5/-0) C 210C 200 250 Temperature( C) 150 30 s minimum30 s maximum 60 s minimum 100 50 0 0 50 100 Time (sec) 150 Note: Peak temperature is 240 (+5 -0)C for less than 10 seconds. Figure 6. Super I/O (PC87338VLJ) to IRMS6453 VCC Figure 8. Super I/O (PC87338VLJ) to IRMS6453 with independent VLED power supply VCC VLED 0.1 F 22 F R0 1 6 LED VCC Anode C1=0.1 F C2=10 F 50 VCC IR TxD 65 PC87338VLJ IR RxD 67 4 R0 C3=0.1 F 1 6 VCC LED Anode 3 TxD C4=22 F 50 VCC IR TxD 65 3 TxD IRMS6453 IRMX6452 PC87338VLJ IR RxD 67 4 RxD SD GND 8 5 GND IRMS6453 IRMX6452 RxD SD 5 GND 8 GND VSS 42 IR SLO 68 VSS 42 IR SLO 68 Table 9. Recommended RO values for different VLED Figure 7. Ultra I/O controller with fast IR (FDC37C93xFR) to IRMS6453 VCC 0.1 F 22 F Parameter VLED power supply Resistor R0 Values 2.7 0 3 1.8 3.3 4.7 >3.5 6.8 Unit V Table 10. Slimline IRMS64XX Truth Table Inputs Outputs VCC 2.4 to 5.5 V 2.4 to 5.5 V 2.4 to 5.5 V 2.4 to 5.5 V 2.4 to 5.5 V 2.4 to 5.5 V Low RxD X=don't care state High Low <0.4 W/cm2 (115 Kb/s) <1.0 W/cm2 (1 & 4 Mb/s) <4.0 W/cm2 (115 Kb/s) <10.0 W/cm2 (1 & 4 Mb/s) Low Off High Detector X=don't care state RxD LED Off On Off SD High Low 125 VCC IR TxD 99 3 1 6 LED VCC Anode TxD IRMS6453 IRMX6452 FDC37C93XFR IR RxD 98 4 RxD SD GND 5 8 GND GND IR MODE 130 19 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 5 IRMS6453 Table 11. Ordering Information Part Number IRMS6453 Description PCB Mounting Orientation Integrated Packaged in Transceiver Component Carrier Reel --Side View (1000/reel) for Side View Mounting on PCB Figure 9. Reel Dimensions in Inches (mm) Matte finish these areas 0.512+0.0208 0.79 - 0 .0 0 (20.2) Min. 13.0 + 0.5 - 0.2 12.97 (330.0) Ref. 4.01 (102.0) Ref. 0.0790.020 (2.0 0.5) X Tape Leader and Trailer is 400 mm minimum. Detail A See detail A W1 (Measured at hub) W2 (Measured at hub) 16.4 mm (+2 mm/-0 mm) 22.4 mm (Max) Figure 10. Tape Dimensions in Inches (mm) IRMT6453 8.00 0.10 4.00 0.10 2.00 .10 o 1.50 .10 1.75 0.10 11.50 .10 24.00 +.30 _.10 5.27 4.01 8 MAX 4.76 0.10 4.32 0.10 11.02 0.10 .356 0.02 3.00 4 MAX 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 6 IRMS6453 Figure 11. IRMS6453 detail drawings with optional side view or top view mounting Dimensions in inches (mm)--All dimensions have tolerances of 0.004" (0.1 mm) 0.304 0.028 TYP. 0.039 TYP. TOP VIEW 12 0.079 0.210 0.006 0.017 0.050 0.098 3456 78 0.059 FRONT VIEW RIGHT SIDE VIEW 0.206 0.120 BACK VIEW 0.163 COPLANER TO .004 0.392 0.422 (c) Infineon Technologies, Corp., Optoelectronic Division (formerly Siemens Microelectronics, Inc.) Printed in the United States of America. All rights reserved. The information provided is believed to be accurate and reliable. Infineon reserves the right to make changes to the product described without notice. No liability is assumed as a result of its use nor for any infringement of the rights of others. This document may contain preliminary information and is subject to change by Infineon without notice. Some of the parametric data expressed in this preliminary data sheet is considered to be functional by design. Infineon assumes no responsibility or liability for any use of the information contained herein. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Infineon or third parties. The products described in this document are not intended for use in implantation or other direct life support applications where malfunction may result in the direct physical harm or injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE OFFERED IN THIS DOCUMENT. 2000 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 7 IRMS6453 |
Price & Availability of IRMS6453
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |