![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
No. STSE-CC6130A SPECIFICATIONS FOR NICHIA CHIP TYPE UV LED MODEL : NCSU033A(T) NICHIA CORPORATION -0- Nichia STSE-CC6130A 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Dice Temperature Symbol IF IFP IR PD Topr Tstg Tj Absolute Maximum Rating 700 1000 85 3.3 -10 ~ + 85 -40 ~ + 100 130 (Ts=25C) Unit mA mA mA W C C C IFP Conditions : Pulse Width < 10msec. and Duty < 1/10 = = (2) Initial Electrical/Optical Characteristics Item Symbol Rank H VF Forward Voltage Rank M VF Rank L VF Peak Wavelength Rank Ua P Spectrum Half Width Rank P7 Po Optical Power Output Rank P6 Po Rank P5 Po Forward Voltage Measurement allowance is 3%. Peak Wavelength Measurement allowance is 3nm. Condition IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] Min. 4.0 3.6 3.2 360 270 230 190 Typ. (365) (9) - Max. 4.4 4.0 3.6 370 310 270 230 (Ts=25C) Unit V V V nm nm mW mW mW Ts : The solder temperature of products (Please refer to the drawing, 061130658591.) Optical Power Output Measurement allowance is 10%. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure's page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure's page. Material as follows ; Package Glass Electrodes : : : Ceramics Hard Glass Au Plating -1- Nichia STSE-CC6130A 4.PACKAGING * The LEDs are packed in cardboard boxes after packaging in moisture proof foil bag. Please refer to figure's page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity (Taped Type) * The LEDs are packed in cardboard boxes after taping. Please refer to figure's page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity * In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. * The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. * The boxes are not water resistant and therefore must be kept away from water and moisture. * When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number - Ranking by Wavelength - Ranking by Optical Power Output - Ranking by Forward Voltage B for Nov. ) -2- Nichia STSE-CC6130A 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Resistance to Soldering Heat (Reflow Soldering) Temperature Cycle High Temperature Storage Low Temperature Storage Steady State Operating Life Condition 1 Steady State Operating Life Condition 2 Steady State Operating Life of High Temperature Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Vibration JEITA ED-4701 400 403 JEITA ED-4701 300 304 JEITA ED-4701 100 105 JEITA ED-4701 200 201 JEITA ED-4701 200 202 Standard Test Method Test Conditions Tsld=260C, 10sec. Note 2 times Number of Damaged 0/10 -40C ~ 25C ~ 100C ~ 25C 30min. 5min. 30min. 5min. Ta=100C Ta=-40C Ta=25C, IF=500mA Tested with Nichia standard circuit board. 100 cycles 500hrs. 500hrs. 500hrs. 500hrs. 500hrs. 500hrs. 500hrs. 48min. 0/10 0/10 0/10 0/10 0/10 0/10 0/10 0/10 0/10 Ta=25C, IF=700mA Tested with Nichia standard circuit board. Ta=85C, IF=300mA Tested with Nichia standard circuit board. 60C, RH=90%, IF=450mA Tested with Nichia standard circuit board. Ta=-10C, IF=500mA Tested with Nichia standard circuit board. Electrostatic Discharge 100 ~ 2000 ~ 100Hz Sweep 4min. 200m/s2 3directions, 4cycles R=1.5k, C=100pF Test Voltage=2kV 3 times Negative/Positive 0/10 Thermal resistance of LED with Nichia standard circuit board : Rja 35C/W (2) CRITERIA FOR JUDGING DAMAGE Item Forward Voltage Symbol VF Test Conditions IF=500mA Criteria for Judgement Min. Max. Initial Level 1.1 Optical Power Output Po IF=500mA Initial Level 0.7 The test is done after the board is cooled down enough at the room temperature. -3- Nichia STSE-CC6130A 7.CAUTIONS (1) Cautions * The devices are UV light LEDs. The LED during operation radiates intense UV light, which precautions must be taken to prevent looking directly at the UV light with unaided eyes. Do not look directly into the UV light or look through the optical system. When there is a possibility to receive the reflection of light, protect by using the UV light protective glasses so that light should not catch one's eye directly. * The caution label is attached to the moisture proof foil bag and cardboard box. ! LED 3B LED UV LED ! DANGER LED RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT (2) Storage * Storage Conditions Before opening the package : The LEDs should be kept at 30C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. * Nichia LED electrodes are gold plated. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. * Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation * Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. * Please decide on operating current volume according to LEDs' ambient temperature and conduct heat release treatment. * The equation 1 indicates correlation between Tj and Ta, and the equation 2 indicates correlation between Tj and Ts. Tj=Ta + Rja W 1 Tj=Ts + Rjs W 2 Tj = Dice Temperature : C, Ta = Ambient Temperature : C, Ts = Solder Temperature : C Rja = Heat resistance from Dice to Ambient temperature : C /W, Rjs = Heat resistance from Dice to Ts measuring point : C /W, W = Inputting Power (IF VF) : W * Maximum Tj shall be under 130C. Keeping Tj less or equal to 100C is recommended. -4- Nichia STSE-CC6130A Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200C 120 ~ 150C 120 sec. Max. 120 sec. Max. 240C Max. 260C Max. 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Although the recommended soldering conditions are specified in the above table, reflow soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. <1 : Lead Solder> 2.5 ~ 5C / sec. Pre-heating 120 ~ 150C 60sec.Max. Above 200C <2 : Lead-free Solder> 240C Max. 10sec. Max. 1~ 5C / sec. 1~ 5C / sec. Pre-heating 180 ~ 200C 60sec.Max. Above 220C 260C Max. 10sec. Max. 2.5 ~ 5C / sec. 120sec.Max. 120sec.Max. [Recommended soldering pad design] 8 .4 4 .2 2 .8 Use the following conditions shown in the figure. 8 .4 7 (Unit : mm) * Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. * Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a hot plate should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. * Reflow soldering should not be done more than two times. * When soldering, do not put stress on the LEDs during heating. * After soldering, do not warp the circuit board. (5) Cleaning * Please do not use ultrasonic cleaning, which may reduce the reliability of the product. -5- Nichia STSE-CC6130A-1 -6- Forward Voltage vs. Forward Current 2000 1000 Ta=25C Relative Power Output (a.u.) Forward Current IFP (mA) Forward Current vs. Relative Power Output 3.0 2.5 2.0 1.5 1.0 0.5 0 0 200 400 600 800 1000 1200 Forward Current IFP (mA) Ta=25C Allowable Forward Current IF (mA) Ambient Temperature vs. Allowable Forward Current 1000 800 600 400 200 0 0 Rja=35C/W Tj =130C 100 10 2.5 3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V) 20 40 60 80 100 Ambient Temperature Ta (C) Ambient Temperature vs. Forward Voltage 5.0 Forward Voltage VF (V) IFP=500mA 4.6 4.2 3.8 3.4 3.0 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Relative Power Output (a.u.) Ambient Temperature vs. Relative Power Output 2.0 IFP=500mA 1.0 -7- 0.5 0.2 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Nichia STSE-CC6130A Model NCSU033A NICHIA CORPORATION Title No. CHARACTERISTICS 061208658971 Forward Current vs. Peak Wavelength Relative Emission Intensity (a.u.) 371 Peak Wavelength p (nm) Ta=25C 369 367 365 363 361 10 100 1000 Forward Current IFP (mA) Spectrum 1.2 1.0 0.8 0.6 0.4 0.2 0 300 350 400 450 500 550 600 Wavelength (nm) Ta=25C IFP=500mA Ambient Temperature vs. Peak Wavelength 371 Relative Power Output (a.u.) Peak Wavelength p (nm) IFP=500mA 369 367 365 363 361 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Directivity 1.0 Ta=25C IFP=500mA 0 10 20 30 40 50 0.5 60 70 80 0 90 60 30 Radiation Angle 0 0.5 90 1.0 -8- Nichia STSE-CC6130A Model NCSU033A NICHIA CORPORATION Title No. CHARACTERISTICS 061208658981 6 .6 6 .8 4 .35 Anode 2 .1 4 .2 2 .8 Cathode ma rk 6 .8 6 .6 LED Die 0 .65 Anode Cathode 0 .65 Cathode Protection device -9Ts ( ) A Ts : Measure point of solder NCSU033A has a protection device built in as a protection circuit against static electricity. ITEM PACKAGE GLASS ELECTRODES MATERIALS Ceramics Hard Glass Au Plating Internal Circuit K Nichia STSE-CC6130A Model NCSU033A Unit mm NICHIA CORPORATION Title No. OUTLINE DIMENSIONS 061130658591 Allow 0.2 12 4 0.1 1.75 0.1 1.5-0 +0.1 2 0.05 0.29 0.1 12-0.1 7.15 0.1 5.5 0.05 1.5-0 +0.25 2.5 0.1 LEDs mounting part Top cover tape Embossed carrier tape 100pcs/bag 7.15 0.1 +0.3 -10- Nichia STSE-CC6130A Model NCxU033x Unit mm Scale Allow NICHIA CORPORATION Title No. PACKING 061130536742 Nichia STSE-CC6130A The IC pack and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. IC pack Label Seal NICHIA UV TYPE LOT QTY LED NCxU033x xxxxxxPCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Caution Label Moisture absorbent material Moisture proof foil bag ! LED 3B LED UV LED ! DANGER LED RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT This Caution Label is applied on Moisture proof foil bag and on Cardboard box. Empty space in the box is filled with cushion material. Label NICHIA Nichia LED UV TYPE RANK QTY LED NCxU033x PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Quantity/bag (pcs) 100 MAX. Dimensions (mm) 250 140 90 4t Bag/box 5bag MAX. Quantity/box (pcs) 500 MAX. Model NCxU033x NICHIA CORPORATION Title No. PACKING 061130536752 -11- Taping part 12 Cathode Reel part 4 0.1 180-3 +0 1.75 0.1 1.5 +0.1 -0 2 0.05 17.5 0.5 13.5 1 0.29 0.1 12-0.1 0.1 +0.3 0.05 7.15 5.5 3 1 .2 0 7.15 0.1 1.5-0 +0.25 2.5 0.1 Label UV TYPE LOT QTY LED NCxU033xT XXXXXX- pcs No LEDs LEDs mounting part No LEDs 60+1 -0 21 0. 8 -12Pull direction Top cover tape Embossed carrier tape 500pcs/Reel Reel Lead Min. 40mm Reel Lead Min. 320mm (No LEDs is more than 27) Reel Lead Min. 400mm Nichia STSE-CC6130A Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. Model NCxU033xT Unit mm Scale Allow NICHIA CORPORATION Title No. TAPING DIMENSIONS 061130536762 Nichia STSE-CC6130A The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label Seal NICHIA UV TYPE LOT QTY LED NCxU033xT xxxxxxPCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Caution Label Moisture absorbent material Moisture proof foil bag ! LED 3B LED UV LED ! DANGER LED RADIATION AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT This Caution Label is applied on Moisture proof foil bag and on Cardboard box. The box is partitioned with the cardboard. Label NICHIA Nichia LED UV TYPE RANK QTY LED NCxU033xT PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 500 MAX. Reel/box 5reel MAX. 10reel MAX. 20reel MAX. Quantity/box (pcs) 2,500 MAX. 5,000 MAX. 10,000 MAX. Dimensions (mm) 291 237 120 8t 259 247 243 5t 444 262 259 8t Model NCxU033xT NICHIA CORPORATION Title No. PACKING 061130542462 -13- |
Price & Availability of NCSU033A
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |