![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
CS53L32A Low Voltage, Stereo A/D Converter FEATURES 20-Pin TSSOP package 1.8 V to 3.3 V supply 24-bit conversion / 96 kHz sample rate 98 dB dynamic range at 3 V supply -88 dBFS THD+N Low power consumption - 11 mW at 1.8 V DESCRIPTION The CS53L32A is a highly integrated, 24-bit, 96 kHz audio ADC providing stereo analog-to-digital converters using delta-sigma conversion techniques. This device includes volume control and line level inputs in a 20-pin TSSOP package. The CS53L32A is based on delta-sigma modulation allowing infinite adjustment of the sample rate between 2 kHz and 100 kHz simply by changing the master clock frequency. The CS53L32A contains adjustable analog gain, a 2:1 input mux, and digital attenuation. The CS53L32A operates from a +1.8 V to +3.3 V supply. These features are ideal for portable MP3 players, MD recorders/players, digital camcorders, PDAs, set-top boxes, and other portable systems that require extremely low power consumption in a minimum of space. Up to 32 dB gain - 20 dB gain step - 12 dB variable input gain, 1 dB steps - Changes made at zero crossings Stereo inputs Digital volume control - 96 dB attenuation, 1 dB step size - Mute - Soft ramping 2:1 Input mux ORDERING INFORMATION CS53L32A-KZ 20-pin TSSOP -10 to 70 C CS53L32A-KZZ 20-pin TSSOP -10 to 70 C CS53L32A-BZ 20-pin TSSOP -40 to 85 C CDB53L32A Evaluation Board Lead free II SCL/CCLK/ ChSEL SDA/CDIN/DIF RST VA VL AD0/CS/DIV Control Port AIN_L1 Serial Port LRCK SCLK SDOUT Attenuator 0-96 dB Attenuator 0-96 dB ADC Digital Filters Gain AIN_L2 ADC AIN_R1 Gain AIN_R2 GND VQ MCLK FILT+ REF_GND AFLTL AFLTR http://www.cirrus.com Copyright (c) Cirrus Logic, Inc. 2004 (All Rights Reserved) OCT `04 DS513F1 CS53L32A TABLE OF CONTENTS 1. CHARACTERISTICS/SPECIFICATIONS ................................................................................. 4 ANALOG CHARACTERISTICS ................................................................................................ 4 ANALOG CHARACTERISTICS ................................................................................................ 5 POWER AND THERMAL CHARACTERISTICS....................................................................... 8 DIGITAL CHARACTERISTICS ................................................................................................. 9 ABSOLUTE MAXIMUM RATINGS ........................................................................................... 9 RECOMMENDED OPERATING CONDITIONS ....................................................................... 9 SWITCHING CHARACTERISTICS ........................................................................................ 10 SWITCHING CHARACTERISTICS - CONTROL PORT - TWO WIRE MODE....................... 12 SWITCHING CHARACTERISTICS - CONTROL PORT - SPI MODE.................................... 13 2. TYPICAL CONNECTION DIAGRAM .................................................................................... 14 3. REGISTER QUICK REFERENCE .......................................................................................... 15 3.1 I/O and Power Control (address 01h) ............................................................................... 15 3.2 Interface Control (address 02h) ........................................................................................ 15 3.3 Analog I/O Control (address 03h) ..................................................................................... 16 3.4 Left Channel Digital Volume Control (address 04h).......................................................... 17 3.5 Right Channel Digital Volume Control (address 05h) ....................................................... 17 3.6 Analog Gain Control (address 06h) .................................................................................. 17 3.7 Clip Detection Status (address 07h) ................................................................................. 17 4. REGISTER DESCRIPTION .................................................................................................... 18 4.1 Gain Enable ...................................................................................................................... 18 4.2 Analog Input Multiplexer ................................................................................................... 18 4.3 Power-Down ..................................................................................................................... 19 4.4 Control Port Enable........................................................................................................... 19 4.5 Master Clock Divide .......................................................................................................... 20 4.6 Master Clock Ratio............................................................................................................ 20 4.7 Master Mode ..................................................................................................................... 21 4.8 Digital Interface Format..................................................................................................... 21 4.9 Left/Right Channel Mute ................................................................................................... 22 4.10 Soft Ramp and Zero Cross Enable ................................................................................. 22 4.11 Independent Volume Control Enable .............................................................................. 23 4.12 Left Channel Volume = Right Channel Volume .............................................................. 24 4.13 High-Pass Filter Freeze .................................................................................................. 24 4.14 Volume Control ............................................................................................................... 25 4.15 Left/Right Analog Gain.................................................................................................... 26 4.16 Clip Detection.................................................................................................................. 26 5. PIN DESCRIPTION ................................................................................................................. 27 6. PIN DESCRIPTION ................................................................................................................. 28 6. PIN DESCRIPTION ................................................................................................................. 28 6. APPLICATIONS ...................................................................................................................... 30 6.1 Grounding and Power Supply Decoupling ....................................................................... 30 6.2 Oversampling Modes ....................................................................................................... 30 6.3 Recommended Power-up Sequence ............................................................................... 30 7. CONTROL PORT INTERFACE ............................................................................................. 30 7.1 SPI Mode ......................................................................................................................... 30 7.2 Two Wire Mode ................................................................................................................ 31 7.3 Memory Address Pointer (MAP) ....................................................................................... 31 8. PARAMETER DEFINITIONS .................................................................................................. 38 9. REFERENCES ........................................................................................................................ 38 10. PACKAGE DIMENSIONS ..................................................................................................... 39 11. CHANGE HISTORY .............................................................................................................. 40 2 DS513F1 CS53L32A LIST OF FIGURES Figure 1. SCLK to LRCK and SDOUT, Slave Mode ..................................................................... 11 Figure 2. SCLK to LRCK and SDOUT, Master Mode ................................................................... 11 Figure 3. Relationship Required Between LRCK and MCLK in Slave Mode ................................ 11 Figure 4. Control Port Timing - Two Wire Mode............................................................................ 12 Figure 5. Control Port Timing - SPI Mode ..................................................................................... 13 Figure 6. Typical Connection Diagram.......................................................................................... 14 Figure 7. Control Port Timing, SPI Mode ...................................................................................... 32 Figure 8. Control Port Timing, Two Wire Mode............................................................................. 32 Figure 9. Base-Rate Stopband Rejection...................................................................................... 33 Figure 10. Base-Rate Transition Band.......................................................................................... 33 Figure 11. Base-Rate Transition Band (Detail) ............................................................................. 33 Figure 12. Base-Rate Passband Ripple........................................................................................ 33 Figure 13. High-Rate Stopband Rejection .................................................................................... 33 Figure 14. High-Rate Transition Band........................................................................................... 33 Figure 15. High-Rate Transition Band (Detail) .............................................................................. 34 Figure 16. High-Rate Passband Ripple......................................................................................... 34 Figure 17. Line Input Test Circuit .................................................................................................. 34 Figure 18. CS53L32A Control Port Mode - Serial Audio Format 0 (I2S) ....................................... 34 Figure 19. CS53L32A Control Port Mode - Serial Audio Format 1 ............................................... 35 Figure 20. CS53L32A Control Port Mode - Serial Audio Format 3 ............................................... 35 Figure 21. CS53L32A Control Port Mode - Serial Audio Format 4 ............................................... 35 Figure 22. CS53L32A Control Port Mode - Serial Audio Format 5 ............................................... 36 Figure 23. CS53L32A Control Port Mode - Serial Audio Format 6 ............................................... 36 Figure 24. CS53L32A Stand-Alone Mode - Serial Audio Format 0 (I2S) ...................................... 36 Figure 25. CS53L32A Stand-Alone Mode - Serial Audio Format 1............................................... 37 LIST OF TABLES Table 1. Analog Input Options....................................................................................................... 18 Table 2. Power-Down Enable ....................................................................................................... 19 Table 3. Control Port Enable......................................................................................................... 19 Table 4. Master Clock Divide Select ............................................................................................. 20 Table 5. MCLK/LRCK Ratios ........................................................................................................ 20 Table 6. Master/Slave Mode Selection ......................................................................................... 21 Table 7. Digital Interface Format................................................................................................... 21 Table 8. Left/Right Channel Mute Enable ..................................................................................... 22 Table 9. Analog Volume Control ................................................................................................... 23 Table 10. Digital Volume Control .................................................................................................. 23 Table 11. Independent Volume Control Enable ............................................................................ 23 Table 12. High-Pass Filter Enable ................................................................................................ 24 Table 13. Example Volume Settings ............................................................................................. 25 Table 14. Example Gain Settings.................................................................................................. 26 Table 15. Clip Detection Status Bits.............................................................................................. 26 Table 16. Common Clock Frequencies......................................................................................... 28 Table 17. Digital Interface Format - DIF (Stand-Alone Mode)....................................................... 28 Table 18. Channel Select Options ................................................................................................ 28 Table 19. Revision Table .............................................................................................................. 40 DS513F1 3 CS53L32A 1. CHARACTERISTICS/SPECIFICATIONS ANALOG CHARACTERISTICS (TA = 25 C; Logic "1" = VL = 1.8 V; Logic "0" = GND = 0 V; MCLK = 12.288 MHz; Fs for Base-rate Mode = 48 kHz, SCLK = 3.072 MHz, Measurement Bandwidth 10 Hz to 20 kHz, unless otherwise specified. Fs for High-Rate Mode = 96 kHz, SCLK = 6.144 MHz, Measurement Bandwidth 10 Hz to 20 kHz, unless otherwise specified. Input signal is a 997 Hz sine wave.) Base-rate Mode Parameter Dynamic Range A-weighted unweighted Symbol Min 88 85 Typ 93 90 -88 -70 -30 -86 -68 -28 Max -83 High-rate Mode Min 89 86 Typ 94 91 -88 -71 -31 -86 -68 -28 Max -83 Unit dB dB dB dB dB dB dB dB CS53L32A-KZ/KZZ Analog Input Characteristics for VA = 1.8 V Total Harmonic Distortion + Noise (Note 1) THD+N 18 to 24-Bit -1 dB -20 dB -60 dB 16-Bit -1 dB -20 dB -60 dB Dynamic Range (PGA on)* 0 dB Gain A-weighted unweighted 12 dB Gain A-weighted unweighted THD+N Total Harmonic Distortion + Noise (PGA on)* (Note 1) 0 dB Gain 18 to 24-Bit -1 dB 12 dB Gain 18 to 24-Bit -1 dB Dynamic Range A-weighted unweighted - 90 87 85 82 - - 89 86 86 83 - dB dB dB dB 91 88 - 85 83 96 93 -88 -73 -33 -86 -68 -28 -83 - 93 90 - 84 82 98 95 -85 -75 -35 -83 -65 -28 -80 - dB dB dB dB dB dB dB dB dB dB CS53L32A-KZ/KZZ Analog Input Characteristics for VA = 3.0 V Total Harmonic Distortion + Noise (Note 1) THD+N 18 to 24-Bit -1 dB -20 dB -60 dB 16-Bit -1 dB -20 dB -60 dB Dynamic Range (PGA on)* 0 dB Gain A-weighted unweighted 12 dB Gain A-weighted unweighted - 93 90 88 85 - - 92 89 89 86 - dB dB dB dB 4 DS513F1 CS53L32A ANALOG CHARACTERISTICS (CONTINUED) Base-rate Mode Parameter Symbol Min Typ Max THD+N Total Harmonic Distortion + Noise (PGA on)* (Note 1) 0 dB Gain 18 to 24-Bit -1 dB 12 dB Gain 18 to 24-Bit -1 dB Interchannel Isolation Interchannel Gain Mismatch Offset Error Full Scale Input Voltage Gain Drift Input Resistance Input Capacitance with High Pass Filter 1 kHz High-rate Mode Min Typ Max Unit -5% 10 - 78 73 90 0.1 VA/3.6 100 93 90 -88 -70 -30 -86 -68 -28 90 87 85 82 0 +5% 15 -81 - -5% 10 87 84 - 77 76 90 0.1 100 94 91 -88 -71 -31 -86 -68 -28 89 86 86 83 0 15 -81 - dB dB dB dB LSB Vrms ppm/C k pF dB dB dB dB dB dB dB dB dB dB dB dB CS53L32A-KZ/KZZ Analog Input Characteristics for VA=1.8 V - 3.3 V VA/3.6 +5% CS53L32A-BZ Analog Input Characteristics for VA = 1.8 V Dynamic Range Total Harmonic Distortion + Noise 18 to 24-Bit A-weighted unweighted (Note 1) THD+N -1 dB -20 dB -60 dB -1 dB -20 dB -60 dB 0 dB Gain A-weighted unweighted 12 dB Gain A-weighted unweighted 86 83 - 16-Bit Dynamic Range (PGA on)* Total Harmonic Distortion + Noise (PGA on)* THD+N (Note 1) 0 dB Gain 18 to 24-Bit -1 dB 12 dB Gain 18 to 24-Bit -1 dB 89 86 85 83 96 93 - 91 88 84 82 98 95 - dB dB dB dB CS53L32A-BZ Analog Input Characteristics for VA = 3.0 V Dynamic Range A-weighted unweighted DS513F1 5 CS53L32A Base-rate Mode Parameter Total Harmonic Distortion + Noise 18 to 24-Bit Symbol (Note 1) THD+N -1 dB -20 dB -60 dB -1 dB -20 dB -60 dB 0 dB Gain A-weighted unweighted 12 dB Gain A-weighted unweighted THD+N Total Harmonic Distortion + Noise (PGA on)* (Note 1) 0 dB Gain 18 to 24-Bit -1 dB 12 dB Gain 18 to 24-Bit -1 dB Min Typ -88 -73 -33 -86 -68 -28 Max -81 High-rate Mode Min Typ -85 -75 -35 -83 -65 -28 Max -78 Unit dB dB dB dB dB dB 16-Bit Dynamic Range (PGA on)* 93 90 88 85 92 89 89 86 dB dB dB dB - 78 73 - - 77 76 - dB dB * PGA = Programmable Gain Amplifier CS53L32A-BZ Analog Input Characteristics for VA=1.8 - 3.3V Interchannel Isolation Interchannel Gain Mismatch Offset Error Full Scale Input Voltage Gain Drift Input Resistance Input Capacitance with High Pass Filter 1 kHz -7% 10 (Note 3) (Note 3) (Note 4) (Note 5) tgd tgd 0 -0.08 27.5 -60.3 90 0.1 VA/3.6 100 1.0 10/Fs 0 +7% 15 0.3 23.5 0.03 -7% 10 0 64.1 -48.4 90 0.1 100 1.0 2.7/Fs 0 15 0.3 47.5 0 0.007 dB dB LSB Vrms ppm/C k pF dB dB kHz dB kHz dB s s VA/3.6 +7% Programmable Gain Characteristics Gain Step Size Absolute Gain Step Error A/D Decimation Filter Characteristics (Note 2) Passband Passband Ripple Stopband Stopband Attenuation Group Delay (Fs = Output Sample Rate) Group Delay Variation vs. Frequency +0.17 -0.09 6 DS513F1 CS53L32A Base-rate Mode Parameter Symbol (Note 2) (Note 2) (Note 2) Min Typ 3.7 24.2 10 Max 0.17 High-rate Mode Min Typ 3.7 24.2 10 Max 0.09 Unit Hz Hz Degree dB High Pass Filter Characteristics Frequency Response Phase Deviation Passband Ripple -3 dB -0.1 dB @ 20 Hz Notes: 1. Referenced to typical full-scale input voltage (0.5 Vrms). 2. Filter response is not tested but is guaranteed by design. 3. Filter characteristics scale with output sample rate. For output sample rates, Fs, other than 48 kHz, the 0.01 dB passband edge is 0.4535x Fs and the stopband edge is 0.625x Fs. 4. The analog modulator samples the input at 6.144 MHz for an Fs equal to 48 kHz. There is no rejection of input signals which are multiples of the sampling frequency (n x 6.144 MHz 21.8 kHz where n = 0,1,2,3...). 5. Group delay for Fs = 48 kHz, tgd = 10/48 kHz = 208 s. DS513F1 7 CS53L32A POWER AND THERMAL CHARACTERISTICS Base-Rate Mode Parameters Symbol VA=1.8 V VL=1.8 V VA=1.8 V VL=1.8 V VA=3.0 V VL=3.0 V VA=3.0 V VL=3.0 V All Supplies=1.8 V All Supplies=3.0 V JA (1 kHz) PSRR (60 Hz) IA ID_IO IA ID_IO IA ID_IO IA ID_IO Min Typ 6.0 150 100 0 9 260 250 0 11 28 75 60 40 Max 12 31 High-Rate Mode Min Typ 7.6 300 250 0 11.5 520 500 0 14.5 36 75 60 40 Max 16 40 Units mA A A A mA A A A mW mW C/Watt dB dB Power Supplies Power Supply CurrentNormal Operation Power Supply CurrentPower Down Mode (Note 6) Power Supply CurrentNormal Operation Power Supply CurrentPower Down Mode Total Power DissipationNormal Operation Package Thermal Resistance Power Supply Rejection Ratio (Note 7) Notes: 6. Power Down Mode is defined as the chip being held in reset with MCLK running. To lower power consumption further, remove MCLK. 7. Valid with the recommended capacitor values on FILT+ and VQ as shown in Figure 6. 8 DS513F1 CS53L32A DIGITAL CHARACTERISTICS (TA = 25 C; VL = 1.7 V - 3.6 V; GND = 0 V) Parameters High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage Leakage Current Input Capacitance Symbol VIH VIL VOH VOL Iin Min 0.7*VL 0.7*VL Typ 8 Max 0.3*VL 0.3*VL 10 Units V V V V A pF ABSOLUTE MAXIMUM RATINGS (GND = 0 V; all voltages with respect to ground.) Parameters DC Power Supplies: Positive Analog Digital I/O Symbol VA VL Iin VIND TA Tstg Min -0.3 -0.3 -0.3 -55 -65 Max 4.0 4.0 10 VL+0.4 125 150 Units V V mA V C C Input Current, Any Pin Except Supplies Digital Input Voltage Ambient Operating Temperature (power applied) Storage Temperature WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (GND = 0V; all voltages with respect to ground.) Parameters Ambient Temperature DC Power Supplies: Positive Analog Digital I/O Symbol TA VA VL Min -10 1.7 1.7 Typ Max 70 3.6 3.6 Units C V V DS513F1 9 CS53L32A SWITCHING CHARACTERISTICS (TA = -10 to 70 C; VA = 1.7 V - 3.6 V; Inputs: Logic 0 = GND, Logic 1 = VL, CL = 20 pF) Parameters Input Sample Rate MCLK Pulse Width High MCLK Pulse Width Low MCLK Pulse Width High MCLK Pulse Width Low MCLK Pulse Width High MCLK Pulse Width Low MCLK Pulse Width High MCLK Pulse Width Low MCLK Pulse Width High MCLK Pulse Width Low Base Rate Mode High Rate Mode MCLK/LRCK = 1024 MCLK/LRCK = 1024 MCLK/LRCK = 768 MCLK/LRCK = 768 MCLK/LRCK = 512 MCLK/LRCK = 512 MCLK / LRCK = 384 or 192 MCLK / LRCK = 384 or 192 MCLK / LRCK = 256 or 128 MCLK / LRCK = 256 or 128 Symbol Fs Fs Min 2 50 8 8 10 10 15 15 21 21 31 31 Typ Max 50 100 Units kHz kHz ns ns ns ns ns ns ns ns ns ns Master Mode SCLK Falling to LRCK Edge SCLK Falling to SDOUT Valid SCLK Duty Cycle tslrd tsdo -20 0 40 50 20 20 60 ns ns % Slave Mode LRCK Duty Cycle Rise Time of Both LRCK and SCLK Fall Time of Both LRCK and SCLK SCLK Period Base Rate Mode High Rate Mode SCLK Falling to LRCK Edge SCLK Falling to SDOUT Valid Base Rate Mode High Rate Mode Notes 8, 9 tr tf tsclkw tsclkw tslrd tdss tdss 1 --------------------( 128 )Fs 1 -----------------( 64 )Fs 50 - 10 10 20 1 (512)Fs 1 (256)Fs % ns ns ns ns ns ns ns -20 - NOTE: When operating the CS53L32A Revision C in Slave Mode, Base Rate Mode, certain timing requirements must be met in addition to those specified above. The required timing relationship between the MCLK and LRCK is shown in Figures 3. An MCLK rising edge cannot lead an LRCK transition by 6ns to 10ns. 8. There must be exactly 32, 48, 64, or 128 SCLK periods per LRCK transition. 9. Slave Mode operation requires an exact 50% duty cycle. Otherwise the CS53L32A will produce erroneous data. 10 DS513F1 CS53L32A t sclkh SCLK t sclkl LRCK t dss SDOUT MSB Figure 1. SCLK to LRCK and SDOUT, Slave Mode t sclkw t slrd SCLK t slrd LRCK t sdo SDOUT MSB MSB-1 Figure 2. SCLK to LRCK and SDOUT, Master Mode LRCK Input 6 ns 10 ns MCLK Input No rising edge of MCLK allowed within this timing window. Figure 3. Relationship Required Between LRCK and MCLK in Slave Mode DS513F1 11 CS53L32A SWITCHING CHARACTERISTICS - CONTROL PORT - TWO WIRE MODE (TA = 25 C; VL = 1.7 V - 3.6 V; Inputs: logic 0 = GND, logic 1 = VL, CL = 30 pF) Parameter Symbol Min Max Unit Two Wire Mode SCL Clock Frequency RST Rising Edge to Start Bus Free Time Between Transmissions Start Condition Hold Time (prior to first clock pulse) Clock Low time Clock High Time Setup Time for Repeated Start Condition SDA Hold Time from SCL Falling SDA Setup time to SCL Rising Rise Time of SCL Fall Time of SCL Rise Time of SDA Fall Time of SDA Setup Time for Stop Condition (Note 10) fscl tirs tbuf thdst tlow thigh tsust thdd tsud trc tfc trd tfd tsusp 500 4.7 4.0 4.7 4.0 4.7 0 250 4.7 100 25 25 1 300 KHz ns s s s s s s ns ns ns us ns s Note: 10. Data must be held for sufficient time to bridge the transition time, tf, of SCL . RST RST t irs t irs Stop Stop SDA Start Start Repeated Repeated Start Start Stop Stop SDA t buf t buf SCL t hdst t hdst t high t t high t hdst tf hdst tf t susp t susp SCL t low t hdd t sud t sust tr t low t hdd t sud t sust tr Figure 4. Control Port Timing - Two Wire Mode 12 DS513F1 CS53L32A SWITCHING CHARACTERISTICS - CONTROL PORT - SPI MODE (TA = 25 C; VL = 1.7V - 3.6V; Inputs: logic 0 = GND, logic 1 = VL, CL = 30 pF) Parameter Symbol Min Max Unit SPI Mode CCLK Clock Frequency RST Rising Edge to CS Falling CCLK Edge to CS Falling CS High Time Between Transmissions CS Falling to CCLK Edge CCLK Low Time CCLK High Time CDIN to CCLK Rising Setup Time CCLK Rising to DATA Hold Time Rise Time of CCLK and CDIN Fall Time of CCLK and CDIN (Note 12) (Note 13) (Note 13) (Note 11) fsclk tsrs tspi tcsh tcss tscl tsch tdsu tdh tr2 tf2 500 500 1.0 20 66 66 40 15 6 100 100 MHz ns ns s ns ns ns ns ns ns ns Notes: 11. tspi only needed before first falling edge of CS after RST rising edge. tspi = 0 at all other times. 12. Data must be held for sufficient time to bridge the transition time of CCLK. 13. For FSCLK < 1 MHz. RST t srs CS t spi t css CCLK t scl t sch t csh t r2 CDIN t f2 t dsu t dh Figure 5. Control Port Timing - SPI Mode DS513F1 13 CS53L32A 2. TYPICAL CONNECTION DIAGRAM *Ferrite bead + 1.0 F 0.1 F 5 VA *Ferrite bead + 1.0 F FILT+ 1 VL 0.1 F REF_GND 16 13 0.1 F + 1.0 F 1.8 to 3.3 V Supply 1.8 to 3.3 V Supply 150 0.47 F ** CS53L32A 18 AIN_L1 VQ 19 0.1 F + 1.0 F 0.01 F 150 0.47 F ** 17 AIN_R1 MCLK LRCK 2 7 3 4 Digital Audio Source 0.01 F 150 0.47 F ** 15 AIN_L2 SCLK SDOUT 0.01 F 150 0.47 F ** 14 AIN_R2 RST SDA/CDIN/DIF SCL/CCLK/ChSEL AD0/CS/DIV 20 9 10 8 12 11 c/ Mode Configuration 0.01 F **Optional if analog input circuit is biased within 5% of CS53L32A nominal bias voltage * Optional GND 6 AFLTL AFLTR 1 nF 1 nF Figure 6. Typical Connection Diagram 14 DS513F1 CS53L32A 3. 3.1 REGISTER QUICK REFERENCE ** "default" ==> bit status after power-up-sequence or reset. I/O and Power Control (address 01h) 6 BOOST 0 5 AINMUX1 0 4 AINMUX0 0 3 RESERVED 0 2 RESERVED 0 1 PDN 1 0 CP_EN 0 7 RESERVED 0 BOOST 20 dB Digital Gain Default = `0' 0 - Disabled 1 - Enabled Analog Input Multiplexer Default ='0'. 0 - AIN_L1/AIN_R1 direct to A/D (default) 1 - AIN_L2/AIN_R2 direct to A/D 2 - AIN_L2/AIN_R2 through PGA to A/D 3 - Reserved Power-Down Default ='1'. 0 - Disabled 1 - Enabled Control Port Enable Default ='0'. 0 - Disabled 1 - Enabled AINMUX PDN CP_EN 3.2 Interface Control (address 02h) 6 MCLKDIV 0 5 RATIO1 0 4 RATIO0 0 3 MASTER 0 2 DIF2 0 1 DIF1 0 0 DIF0 0 7 RESERVED 0 MCLKDIV Master Clock Divider Default ='0'. 0 - Disabled 1 - Enabled Master Clock Ratio Default ='0'. 0 - 128x (default) 1 - 192x 2 - 256x 3 - 384x Master Mode Default ='0'. 0 - Slave Mode 1 - Master Mode RATIO1-0 MASTER DS513F1 15 CS53L32A DIF2-0 Digital Interface Format Default = `0'. 0 - I2S, up to 24-bit Data, Data valid on positive edge of SLCK (default) 1 - Left Justified, up to 24-bit Data, Data valid on positive edge of SLCK 2 - Reserved 3 - Right Justified, 16-bit Data, Data valid on positive edge of SLCK 4 - Right Justified, 24-bit Data, Data valid on positive edge of SLCK 5 - Right Justified, 18-bit Data, Data valid on positive edge of SLCK 6 - Right Justified, 20-bit Data, Data valid on positive edge of SLCK 7 - Reserved 3.3 Analog I/O Control (address 03h) 6 MUTER 0 5 SOFT 1 4 ZC 1 3 RESERVED 0 2 INDVC 0 1 L=R 0 0 HPFREEZE 0 7 MUTEL 0 MUTEL Left Channel Mute Default = `0'. 0 - Disabled 1 - Enabled Right Channel Mute Default = `0'. 0 - Disabled 1 - Enabled Soft Digital/Analog Volume Control Default = `1'. 0 - Disabled 1 - Enabled Analog Zero Cross Detection Control Default = `1'. 0 - Disabled 1 - Enabled Independent Volume Control Enable Default = `0'. 0 - Disabled 1 - Enabled Left Channel Volume = Right Channel Volume Default = `0'. 0 - Left channel volume is determined by the left channel volume control registers and right channel volume is determined by the right channel volume control registers. 1 - Left and right channel volumes are determined by the left channel volume control registers and the right channel volume control registers are ignored. High-pass filter freeze Default = `0'. 0 - Disabled 1 - Enabled MUTER SOFT ZC INDVC L=R HPFREEZE 16 DS513F1 CS53L32A 3.4 3.5 Left Channel Digital Volume Control (address 04h) Right Channel Digital Volume Control (address 05h) 7 VOL7 0 6 VOL6 0 5 VOL5 0 4 VOL4 0 3 VOL3 0 2 VOL2 0 1 VOL1 0 0 VOL0 0 VOL7-0 Volume Default = `0'. (Refer to Table 13) 3.6 Analog Gain Control (address 06h) 7 LVOL3 0 6 LVOL2 0 5 LVOL1 0 4 LVOL0 0 3 RVOL3 0 2 RVOL2 0 1 RVOL1 0 0 RVOL0 0 LVOL3-0 Left Analog Gain Default = `0'. (Refer to Table 14) Right Analog Gain Default = `0'. (Refer to Table 14) RVOL3-0 3.7 Clip Detection Status (address 07h) 6 RESERVED 0 5 RESERVED 0 4 RESERVED 0 3 RESERVED 0 2 RESERVED 0 1 0 CLIP_L_FLAG CLIP_R_FLAG 0 0 7 RESERVED 0 CLIP_L_FLAG CLIP_R_FLAG Left Channel Clip Detection Right Channel Clip Detection Default = `0'. 0 - No Clipping Detected 1 - Clipping Detected DS513F1 17 CS53L32A 4. 4.1 REGISTER DESCRIPTION GAIN ENABLE I/O and Power Control Register (address 01h) 7 RESERVED 6 BOOST 5 AINMUX1 4 AINMUX0 3 RESERVED 2 RESERVED 1 PDN 0 CP_EN Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Disabled Function: Applies a 20 dB digital gain to the input signal, regardless of the input path. 4.2 ANALOG INPUT MULTIPLEXER I/O and Power Control Register (address 01h) 7 RESERVED 6 BOOST 5 AINMUX1 4 AINMUX0 3 RESERVED 2 RESERVED 1 PDN 0 CP_EN Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - AIN_L1/AIN_R1 direct to A/D Function: The analog input multiplexer selects the input channel as well as the input path associated with various gain stages. AINMUX 0 1 2 3 MODE AIN_L1/AIN_R1 direct to A/D AIN_L2/AIN_R2 direct to A/D AIN_L2/AIN_R2 through PGA to A/D Reserved Table 1. Analog Input Options 18 DS513F1 CS53L32A 4.3 POWER-DOWN I/O and Power Control Register (address 01h) 7 RESERVED 6 BOOST 5 AINMUX1 4 AINMUX0 3 RESERVED 2 RESERVED 1 PDN 0 CP_EN Access: R/W in Two Wire Mode and write only in SPI. Default: 1 - Enabled Function: The entire device will enter a low-power state whenever this function is activated. The power-down bit defaults to `enabled' on power-up and must be disabled before normal operation will begin. The contents of the control registers are retained when this mode is enabled. PDN 0 1 MODE Disabled Enabled Table 2. Power-Down Enable 4.4 CONTROL PORT ENABLE I/O and Power Control Register (address 01h) 7 RESERVED 6 BOOST 5 AINMUX1 4 AINMUX0 3 RESERVED 2 RESERVED 1 PDN 0 CP_EN Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Disabled Function: The CS53L32A will enter Control Port mode when this bit is enabled. Stand-Alone is the default power up mode. See Section 6.3, Recommended Power-up Sequence, for more details. CP_EN 0 1 MODE Disabled Enabled Table 3. Control Port Enable DS513F1 19 CS53L32A 4.5 MASTER CLOCK DIVIDE Interface Control Register (address 02h) 7 RESERVED 6 MCLKDIV 5 RATIO1 4 RATIO0 3 MASTER 2 DIF2 1 DIF1 0 DIF0 Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Disabled Function: Divides MCLK by two prior to all other chip circuitry. MCLKDIV 0 1 MODE Disabled Enabled Table 4. Master Clock Divide Select 4.6 MASTER CLOCK RATIO Interface Control Register (address 02h) 7 RESERVED 6 MCLKDIV 5 RATIO1 4 RATIO0 3 MASTER 2 DIF2 1 DIF1 0 DIF0 Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - 128x Function: Sets the ratio of MCLK to LRCK. RATIO1,0 0 1 2 3 MCLK/LRCK RATIO (MCLKDIV=0) 128x 192x 256x 384x MCLK/LRCK RATIO (MCLKDIV=1) 256x 384x 512x 768x Table 5. MCLK/LRCK Ratios 20 DS513F1 CS53L32A 4.7 MASTER MODE Interface Control Register (address 02h) 7 RESERVED 6 MCLKDIV 5 RATIO1 4 RATIO0 3 MASTER 2 DIF2 1 DIF1 0 DIF0 Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Slave Mode Function: Configures the device for master or slave operation when in Control Port mode. MASTER 0 1 MODE Slave Mode Master Mode Table 6. Master/Slave Mode Selection 4.8 DIGITAL INTERFACE FORMAT Interface Control Register (address 02h) 7 RESERVED 6 MCLKDIV 5 RATIO1 4 RATIO0 3 MASTER 2 DIF2 1 DIF1 0 DIF0 Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Format 0 (I2S, up to 24-bit data, Data valid on positive edge of SCLK) Function: The required relationship between the Left/Right clock, serial clock and serial data is defined by the Digital Interface Format and the options are detailed in Figures 18 through 21. DIF2 DIF1 DIF0 DESCRIPTION 0 0 0 I2S, up to 24-bit Data, Data valid on positive edge of SCLK 0 0 1 Left Justified, up to 24-bit Data, Data valid on positive edge of SCLK 0 1 0 Reserved 0 1 1 Right Justified, 16-bit Data, Data valid on positive edge of SCLK 1 0 0 Right Justified, 24-bit Data, Data valid on positive edge of SCLK 1 0 1 Right Justified, 18-bit Data, Data valid on positive edge of SCLK 1 1 0 Right Justified, 20-bit Data, Data valid on positive edge of SCLK 1 1 1 Reserved Table 7. Digital Interface Format Format 0 FIGURE 18 1 2 3 4 5 6 7 19 18 19 20 21 - DS513F1 21 CS53L32A 4.9 LEFT/RIGHT CHANNEL MUTE Analog I/O Control (address 03h) 7 MUTEL 6 MUTER 5 SOFT 4 ZC 3 RESERVED 2 INDVC 1 L=R 0 HPFREEZE Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Disabled Function: Digital mute of the left and right channels. MUTEL/ MUTER 0 1 MODE Disabled Enabled Table 8. Left/Right Channel Mute Enable 4.10 SOFT RAMP AND ZERO CROSS ENABLE Analog I/O Control Register (address 03h) 7 MUTEL 6 MUTER 5 SOFT 4 ZC 3 RESERVED 2 INDVC 1 L=R 0 HPFREEZE Access: R/W in Two Wire Mode and write only in SPI. Default: 11 - Soft Ramp and Zero Cross enabled Function: Soft Ramp Enable Soft Ramp allows level changes, both muting and attenuation, to be implemented via an incremental ramp. Digital volume control is ramped from the current level to the new level at a rate of 1/8 dB per left/right clock period. Analog volume control is ramped in 1 dB steps every 8 left/right clock periods in Base Rate mode, and 1 dB every 16 left/right clock periods in High Rate mode. Zero Cross Enable Zero Cross Enable dictates that signal level changes, either by attenuation changes or muting, will occur on a signal zero crossing to minimize audible artifacts. The requested level change will occur after a timeout period of 512 sample periods in BRM or 1024 sample periods in HRM (approximately 10.7 ms at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel. 22 DS513F1 CS53L32A Soft Ramp and Zero Cross Enable Soft Ramp and Zero Cross Enable dictates that signal level changes, either by attenuation changes or muting, will occur in 1 dB steps and be implemented on a signal zero crossing. The level change will occur after a timeout period of 512 sample periods in BRM or 1024 sample periods in HRM (approximately 10.7 ms at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel. SOFT/ZC 00 01 10 11 ANALOG VOLUME CONTROL MODES Change volume immediately Change volume at next zero cross time Change volume in 1 dB steps Change volume in 1 dB steps at every zero cross time Table 9. Analog Volume Control . SOFT 0 1 DIGITAL VOLUME CONTROL MODES Change volume immediately Change volume in1/8 dB steps Table 10. Digital Volume Control 4.11 INDEPENDENT VOLUME CONTROL ENABLE Analog I/O Control Register (address 03h) 7 MUTEL 6 MUTER 5 SOFT 4 ZC 3 RESERVED 2 INDVC 1 L=R 0 HPFREEZE Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Enabled Function: When this function is disabled, the AIN_L and AIN_R volume levels are controlled by the Left and Right Volume Control registers and the Independent Analog Gain Control registers are ignored. When this function is enabled, the volume levels are determined by both the Volume Control registers and the Independent Analog Gain Control registers. INDVC 0 1 MODE Enabled Frozen Table 11. Independent Volume Control Enable DS513F1 23 CS53L32A 4.12 LEFT CHANNEL VOLUME = RIGHT CHANNEL VOLUME Analog I/O Control (address 03h) 7 MUTEL 6 MUTER 5 SOFT 4 ZC 3 RESERVED 2 INDVC 1 L=R 0 HPFREEZE Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Disabled Function: When this function is disabled, the left channel volume is determined by the left channel volume control register and right channel volume is determined by the right channel volume control register. When enabled, the left and right channel volumes are determined by the left channel volume control register and the right channel volume control register is ignored. 4.13 HIGH-PASS FILTER FREEZE Analog I/O Control Register (address 03h) 7 MUTEL 6 MUTER 5 SOFT 4 ZC 3 RESERVED 2 INDVC 1 L=R 0 HPFREEZE Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - Enabled Function: The high-pass filter works by continuously subtracting a measure of the dc offset from the output of the decimation filter. If the HPFREEZE bit is taken low during normal operation, the current value of the dc offset is frozen and this dc offset will continue to be subtracted from the conversion result. This feature makes it possible to perform a system calibration by: 1) removing the signal source at the input to the subsystem containing the CS53L32A, 2) running the CS53L32A with the HPFREEZE bit high until the filter settles, approximately one second, 3) taking the HPFREEZE bit low, thus disabling the high-pass filter and freezing the stored dc offset. A system calibration performed in this way will eliminate offsets anywhere in the signal path between the calibration point and the CS53L32A. HPFREEZE 0 1 MODE Enabled Frozen Table 12. High-Pass Filter Enable 24 DS513F1 CS53L32A 4.14 VOLUME CONTROL Left Channel Volume Control Register (address 04h) Right Channel Volume Control Register (address 05h) 7 VOL7 6 VOL6 5 VOL5 4 VOL4 3 VOL3 2 VOL2 1 VOL1 0 VOL0 Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - 0 dB (No attenuation) Function: The Volume Control allows the user to alter the signal level in 1 dB increments from +12 to -96 dB, when the INDVC bit is disabled. When INDVC is enabled, the Volume Control can be altered in 1 dB increments from 0 to -96 dB. Volume settings are decoded as shown in Table 13, using a 2's complement code. The volume changes are implemented as dictated by the Soft and Zero Cross bits in the Analog I/O Control register. All volume settings less than -96 dB are equivalent to muting the channel. Binary Code 00001010 00000111 00000000 11000100 10100110 Decimal Value 12 7 0 -60 -90 Volume Setting +12 dB +7 dB 0 dB -60 dB -90 dB Table 13. Example Volume Settings DS513F1 25 CS53L32A 4.15 LEFT/RIGHT ANALOG GAIN ADC Independent Analog Gain Control Register (address 06h) 7 LVOL3 6 LVOL2 5 LVOL1 4 LVOL0 3 RVOL3 2 RVOL2 1 RVOL1 0 RVOL0 Access: R/W in Two Wire Mode and write only in SPI. Default: 0 - 0 dB (No Gain) Function: The level of the left and right analog channels can be adjusted in 1 dB increments as dictated by the Soft Ramp and Zero Cross bits from 0 to +12 dB when routed through the PGA via the AINMUX bits in Control Port mode or the CH_SEL pins in Stand-Alone mode. Levels are decoded as shown in Table 14. Levels above +12 dB are interpreted as +12 dB. Binary Code 0000 0010 1010 1001 1100 Decimal Value 0 2 6 9 12 Volume Setting 0 dB +2 dB +6 dB +9 dB +12 dB Table 14. Example Gain Settings 4.16 CLIP DETECTION Clip Detection Status Register (address 07h) 7 RESERVED 6 RESERVED 5 RESERVED 4 RESERVED 3 RESERVED 2 RESERVED 1 0 CLIP_L_FLAG CLIP_R_FLAG Access: Read only in Two Wire Mode and unavailable in SPI. Default: 0 - No Clipping Detected Function: The Clip Flags indicate when there is an over-range condition anywhere in the CS53L32A internal signal path. These bits are "sticky". They constantly monitor the ADC signal path and are set to 1 when an overrange condition occurs. They are reset to 0 when read. CLIP_L_FLAG CLIP_R_FLAG 0 1 Condition Signal within normal range Signal is over-range Table 15. Clip Detection Status Bits 26 DS513F1 CS53L32A 5. PIN DESCRIPTION 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 RST VQ AIN_L1 AIN_R1 REF_GND AIN_L2 AIN_R2 FILT+ AFLTL AFLTR Reset Quiescent Voltage Analog Input 1 Left Analog Input 1 Right Reference Ground Analog Input 2 Left Analog Input 2 Right Positive Voltage Reference Anti-Aliasing Capacitor Anti-Aliasing Capacitor Interface Power VL Master Clock MCLK Serial Clock SCLK Serial Audio Data Out SDOUT Analog Power VA Ground GND Left/Right Clock LRCK AD0/CS/DIV AD0/CS/DIV SDA/CDIN/DIF SDA/CDIN/DIF SCL/CCLK/ChSEL SCL/CCLK/ChSEL Interface Power Master Clock 1 2 VL (Input) - Digital interface power supply. Typically 1.8 to 3.3 VDC. MCLK (Input) - The master clock frequency must be either 256x, 384x, 512x, 768x or 1024x the input sample rate in Base Rate Mode (BRM) and 128x, 192x, 256x, 384x the input sample rate in High Rate Mode (HRM). Table 16 illustrates several standard audio sample rates and the required master clock frequencies. SCLK (Input/Output) - Clocks the individual bits of the serial data out of the SDOUT pin. The required relationship between the Left/Right clock, serial clock and serial data is defined by the DIF2-0 bytes when in Control Port mode or by the DIF1-0 pins when in Stand-Alone mode. SDOUT (Output) - This pin serves two functions. First: Two's complement MSB-first serial data is output on this pin. The data is clocked out of SDOUT via the serial clock and the channel is determined by the Left/Right clock. The required relationship between the Left/Right clock, serial clock and serial data is defined by the DIF2-0 bytes when in Control Port mode or by the DIF pin when in Stand-Alone mode. Second: In Stand-alone mode, Master/Slave mode selection is determined, at start-up, by a 47 kOhm pull-up/pull-down on this line. A pull-up to VL selects Master mode and a pull-down to GND selects Slave mode. VA (Input) - Analog power supply. Typically 1.8 to 3.3 VDC. GND (Input) - Ground Reference. LRCK (Input/Output) - The Left/Right clock determines which channel is currently being output on the serial audio data line SDOUT. The frequency of the Left/Right clock must be at the input sample rate. The required relationship between the Left/Right clock, serial clock and serial data is defined by the DIF2-0 bytes when in Control Port mode or by the DIF pin when in Stand-Alone mode. Serial Clock 3 Serial Audio Data Out 4 Analog Power Ground Left/Right Clock 5 6 7 DS513F1 27 CS53L32A MCLK (MHz) Sample Rate (kHz) 32 44.1 48 64 88.2 96 HRM 128x 192x 256x* 384x* 256x 384x BRM 512x 768x* 1024x* 4.0960 5.6448 6.1440 8.1920 11.2896 12.2880 6.1440 8.4672 9.2160 12.2880 16.9344 18.4320 8.1920 11.2896 12.2880 16.3840 22.5792 24.5760 12.2880 16.9344 18.4320 24.5760 33.8688 36.8640 8.1920 11.2896 12.2880 - 12.2880 16.9344 18.4320 - 16.3840 22.5792 24.5760 - 24.5760 32.7680 36.8640 - 32.7680 45.1584 49.1520 - * MCLKDIV = 1 in Control Port mode or DIV= Hi when in Stand-Alone mode Table 16. Common Clock Frequencies Address Bit MCLK Divide Enable Serial Control Data I/O 8 8 9 AD0/CS (Control Port Mode) (Input) - In Two Wire mode, AD0 is a chip address bit. CS is used to enable the control port interface in SPI mode. DIV (Stand-Alone Mode) (Input) - When high, the chip will enter High Rate Mode. When this pin is low, the chip will enter Base Rate Mode. SDA/CDIN (Control Port Mode) (Input/Output) - In Two Wire mode, SDA is a data I/O line. CDIN is the input data line for the control port interface in SPI mode. DIF (Stand-Alone Mode) (Input) - The required relationship between the Left/Right clock, serial clock and serial data is defined by the Digital Interface Format. DIF 0 1 DESCRIPTION I2S, up to 24-bit data Left Justified, up to 24-bit data Digital Interface Format 9 Table 17. Digital Interface Format - DIF (Stand-Alone Mode) Serial Control Interface Clock Channel Select 10 10 SCL/CCLK (Control Port Mode) (Input) - Clocks the serial control data into or from SDA/CDIN/DIF. ChSEL (Stand-Alone Mode) (Input) - The analog data path is determined by the Channel Select bit. These options are detailed in Table 18. ChSEL 0 1 DESCRIPTION Channel 1 directly to A/D Channel 2 with 32dB of gain Table 18. Channel Select Options Anti-Aliasing Capacitors 11, 12 AFLTR, AFLTL (Output) - Anti-aliasing capacitors for the left and right channels. An external capacitor is required from AFLTR and AFLTL to ground, as shown in Figure 5. AFLTR and AFLTL are not intended to supply external current, and any current drawn from these pins will alter device performance. FILT+ (Output) - Positive reference for internal sampling circuits. An external capacitor is required from FILT+ to ground, as shown in Figure 6. The recommended value will typically provide 60 dB of PSRR at 1 kHz and 40 dB of PSRR at 60 Hz. FILT+ is not intended to supply external current. FILT+ has a typical source impedance of 250 k and any current drawn from this pin will alter device performance. AIN_R1, AIN_L1, AIN_R2, AIN_L2 (Input) - Channel 1/Channel 2 analog inputs. Positive Voltage Reference 13 Analog Inputs 14, 15, 17, and 18 28 DS513F1 CS53L32A Reference Ground Quiescent Voltage 16 19 REF_GND (Input) - Ground reference for the internal sampling circuits. Must be connected to ground. VQ (Output) - Filter connection for internal A/D converter quiescent reference voltage. A capacitor must be connected from VQ to ground. VQ is not intended to supply external current. VQ has a typical source impedance of 250 k and any current drawn from this pin will alter device performance. RST (Input) - The device enters a low power mode and all internal registers are reset to their default settings, including the control port, when low. When high, the control port becomes operational and the PDN bit must be cleared before normal operation will occur. The control port cannot be accessed when Reset is low. Reset 20 DS513F1 29 CS53L32A 6. APPLICATIONS 6.1 GROUNDING AND POWER SUPPLY DECOUPLING As with any high resolution converter, the CS53L32A requires careful attention to power supply and grounding arrangements to optimize performance. Figure 6 shows the recommended power arrangement with VA and VL connected to clean supplies. Decoupling capacitors should be located as close to the device package as possible. 6.2 OVERSAMPLING MODES The CS53L32A operates in one of two oversampling modes. Base Rate Mode supports input sample rates up to 50 kHz while High Rate Mode supports input sample rates up to 100 kHz. See Table 16 for more details. 6.3 RECOMMENDED POWER-UP SEQUENCE 1) Hold RST low until the power supply, master, and left/right clocks are stable. In this state, the control port is reset to its default settings and VQ will remain low. 2) Bring RST high. The device will remain in a low power state with VQ low and will initiate the StandAlone power-up sequence. The control port will be accessible at this time. If control port operation is desired, write the CP_EN bit prior to the completion of the Stand-Alone power-up sequence, approximately 1024 LRCK cycles. Writing this bit will halt the Stand-Alone power-up sequence and initialize the control port to its default settings. The desired register settings can be loaded while keeping the PDN bit set to 1. 3) If Control Port mode is selected via the CP_EN bit, set the PDN bit to 0 which will initiate the powerup sequence, which requires approximately 50 S. 7. CONTROL PORT INTERFACE The control port is used to load all the internal settings. The operation of the control port may be completely asynchronous with the audio sample rate. However, to avoid potential interference problems, the control port pins should remain static if no operation is required. The control port has 2 modes: SPI and Two Wire. If Two Wire operation is desired, AD0/CS should be tied to VL or GND. If the CS53L32A ever detects a high to low transition on AD0/CS after power-up, SPI mode will be selected. 7.1 SPI MODE In SPI mode, CS is the CS53L32A chip select signal, CCLK is the control port bit clock, CDIN is the input data line from the microcontroller and the chip address is 0010000. All signals are inputs and data is clocked in on the rising edge of CCLK. All CS53L32A registers are write-only in SPI mode. Figure 7 shows the operation of the control port in SPI mode. To write to a register, bring CS low. The first 7 bits on CDIN form the chip address, and must be 0010000. The eighth bit is a read/write indicator (R/W), which must be low to write. The next 8 bits form the Memory Address Pointer (MAP), which is set to the address of the register that is to be updated. The next 8 bits are the data which will be placed into the register designated by the MAP. The CS53L32A has a MAP auto increment capability, enabled by the INCR bit in the MAP. If INCR is a zero, then the MAP will stay constant for successive writes. If INCR is set to a 1, then MAP will auto increment after each byte is written, allowing block writes of successive registers. 30 DS513F1 CS53L32A 7.2 TWO WIRE MODE In Two Wire mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL, with the clock to data relationship as shown in Figure 8. There is no CS pin. Pin AD0 forms the partial chip address and should be tied to VL or GND as required. The upper 6 bits of the 7 bit address field must be 001000. To communicate with the CS53L32A the LSB of the chip address field, which is the first byte sent to the CS53L32A, should match the setting of the AD0 pin. The eighth bit of the address byte is the R/W bit (high for a read, low for a write). If the operation is a write, the next byte is the Memory Address Pointer which selects the register to be read or written. See Section 7.3, Memory Address Pointer (MAP). If the operation is a read, the contents of the register pointed to by the Memory Address Pointer will be output. Setting the auto increment bit in MAP, allows successive reads or writes of consecutive registers. Each byte is separated by an acknowledge bit. Note: The Two-Wire control port mode is compatible with the I2C protocol. 7.3 MEMORY ADDRESS POINTER (MAP) 7 INCR 0 6 Reserved 0 5 Reserved 0 4 Reserved 0 3 Reserved 0 2 MAP2 0 1 MAP1 0 0 MAP0 0 INCR (Auto MAP Increment Enable) Default = `0'. 0 - Disabled 1 - Enabled MAP0-2 (Memory Address Pointer) Default = `000'. DS513F1 31 CS53L32A CS CCLK CHIP ADDRESS CDIN 0010000 R/W MAP MSB DATA LSB byte 1 MAP = Memory Address Pointer byte n Figure 7. Control Port Timing, SPI Mode Note 1 SDA 001000 ADDR AD0 R/W ACK DATA 1-8 ACK DATA 1-8 ACK SCL Start Stop Note: If operation is a write, this byte contains the Memory Address Pointer, MAP. Figure 8. Control Port Timing, Two Wire Mode 32 DS513F1 CS53L32A 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency (normalized to Fs ) 0 -10 -20 Amplitude dB -30 -40 -50 -60 -70 -80 -90 -100 0.4 0.42 0.44 0.46 0.48 0.5 0.52 0.54 0.56 0.58 0.6 Amplitude dB Frequency (normalized to Fs) Figure 9. Base-Rate Stopband Rejection 0 -1 -2 Amplitude dB -4 -5 -6 -7 -8 -9 -10 0.45 0.46 0.47 0.48 0.49 0.5 0.51 0.52 0.53 0.54 0.55 Amplitude dB Figure 10. Base-Rate Transition Band 0.3 0.25 0.2 0.15 0.1 0.05 0 -0.05 -0.1 -0.15 -0.2 -0.25 -0.3 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Frequency (normalized to Fs) -3 Frequency (normalized to Fs ) Figure 11. Base-Rate Transition Band (Detail) Figure 12. Base-Rate Passband Ripple 0 -10 -20 Amplitude dB -40 -50 -60 -70 -80 -90 -100 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Frequency (normalized to Fs) -30 0 -10 -20 Amplitude dB -30 -40 -50 -60 -70 -80 -90 -100 0.4 0.43 0.46 0.49 0.52 0.55 0.58 0.61 0.64 0.67 Frequency (normalized to Fs) Figure 13. High-Rate Stopband Rejection Figure 14. High-Rate Transition Band DS513F1 33 CS53L32A 0 -1 -2 Amplitude dB -4 -5 -6 -7 -8 -9 -10 0.45 0.46 0.47 0.48 0.49 0.5 0.51 0.52 0.53 0.54 0.55 Amplitude dB -3 0.3 0.25 0.2 0.15 0.1 0.05 0 -0.05 -0.1 -0.15 -0.2 -0.25 -0.3 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Frequency (normalized to Fs) Frequency (normalized to Fs ) Figure 15. High-Rate Transition Band (Detail) Figure 16. High-Rate Passband Ripple 150 0.47 F AIN_xx 0.01 F GND Figure 17. Line Input Test Circuit LRCK SCLK Left Channel Right Channel SDATA MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB I2S, up to 24-Bit Data. Data Valid on Rising Edge of SCLK. Figure 18. CS53L32A Control Port Mode - Serial Audio Format 0 (I2S) 34 DS513F1 CS53L32A LRCK SCLK Left Channel Right Channel SDATA MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB Left Justified, up to 24-Bit Data. Data Valid on Rising Edge of SCLK. Figure 19. CS53L32A Control Port Mode - Serial Audio Format 1 LRCK Right Channel Left Channel SCLK SDATA 15 14 13 12 11 10 9 8 7 65 43 21 0 15 14 13 12 11 10 9 876 5 432 10 Right 32 clocks Justified, 16-Bit Data. Data Valid on Rising Edge of SCLK. SCLK Must Have at Least 32 Cycles per LRCK Period. Figure 20. CS53L32A Control Port Mode - Serial Audio Format 3 LRCK Left Channel Right Channel SCLK SDATA 0 23 22 21 20 19 18 765 43210 23 22 21 20 19 18 76543210 32 clocks Right Justified, 24-Bit Data. Data Valid on Rising Edge of SCLK. SCLK Must Have at Least 48 Cycles per LRCK Period. Figure 21. CS53L32A Control Port Mode - Serial Audio Format 4 DS513F1 35 CS53L32A Right Channel LRCK Left Channel SCLK SDATA 10 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 32 clocks Right Justified, 20-Bit Data. Data Valid on Rising Edge of SCLK. SCLK Must Have at Least 40 Cycles per LRCK Period. Figure 23. CS53L32A Control Port Mode - Serial Audio Format 6 LRCK SCLK Left Channel Right Channel SDATA MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB I2S, up to 24-Bit Data. Data Valid on Rising Edge of SCLK Figure 24. CS53L32A Stand-Alone Mode - Serial Audio Format 0 (I2S) LRCK Left Channel Right Channel SCLK SDATA 1 0 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 32 clocks Right Justified, 18-Bit Data. Data Valid on Rising Edge of SCLK. SCLK Must Have at Least 36 Cycles per LRCK Period. Figure 22. CS53L32A Control Port Mode - Serial Audio Format 5 36 DS513F1 CS53L32A LRCK SCLK Left Channel Right Channel SDATA MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB Left Justified, up to 24-Bit Data. Data Valid on Rising Edge of SCLK. Figure 25. CS53L32A Stand-Alone Mode - Serial Audio Format 1 DS513F1 37 CS53L32A 8. PARAMETER DEFINITIONS Total Harmonic Distortion + Noise (THD+N) The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Dynamic Range The ratio of the full scale rms value of the signal to the rms sum of all other spectral components over the specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth made with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement to full scale. This technique ensures that the distortion components are below the noise level and do not effect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307. Interchannel Isolation A measure of crosstalk between the left and right channels. Measured for each channel at the converter's output with all zeros to the input under test and a full-scale signal applied to the other channel. Units in decibels. Interchannel Gain Mismatch The gain difference between left and right channels. Units in decibels. Gain Error The deviation from the nominal full scale analog output for a full scale digital input. Gain Drift The change in gain value with temperature. Units in ppm/C. 9. REFERENCES 1. "How to Achieve Optimum Performance from Delta-Sigma A/D & D/A Converters" by Steven Harris. Paper presented at the 93rd Convention of the Audio Engineering Society, October 1992. 2. CDB53L32 Evaluation Board Datasheet. 38 DS513F1 CS53L32A 10.PACKAGE DIMENSIONS 20L TSSOP (4.4 mm BODY) PACKAGE DRAWING N D E11 A2 A1 L E A e b2 SIDE VIEW 123 END VIEW SEATING PLANE TOP VIEW INCHES DIM A A1 A2 b D E E1 e L MIN -0.002 0.03346 0.00748 0.252 0.248 0.169 -0.020 0 NOM -0.004 0.0354 0.0096 0.256 0.2519 0.1732 -0.024 4 MAX 0.043 0.006 0.037 0.012 0.259 0.256 0.177 0.026 0.028 8 MIN -0.05 0.85 0.19 6.40 6.30 4.30 -0.50 0 MILLIMETERS NOM --0.90 0.245 6.50 6.40 4.40 -0.60 4 MAX 1.10 0.15 0.95 0.30 6.60 6.50 4.50 0.65 0.70 8 NOTE 2,3 1 1 JEDEC #: MO-153 Controlling Dimension is Millimeters. Notes: 1. "D" and "E1" are reference datums and do not included mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm per side. 2. Dimension "b" does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be 0.13 mm total in excess of "b" dimension at maximum material condition. Dambar intrusion shall not reduce dimension "b" by more than 0.07 mm at least material condition. 3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips. DS513F1 39 CS53L32A 11.CHANGE HISTORY Table 19. Revision Table Revision Date Change PP1 PP2 F1 July 2000 September 2004 October 2004 Initial release Added part number CS53L32A-KZZ, lead free package option. Updated Min/Max Specifications Integrated Errata ER513B1 Integrated Errata ER513B2 Integrated Errata ER513C1 Contacting Cirrus Logic Support For a complete listing of Direct Sales, Distributor, and Sales Representative contacts, visit the Cirrus Logic web site at: http://www.cirrus.com/ Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS (INCLUDING MEDICAL DEVICES, AIRCRAFT SYSTEMS OR COMPONENTS AND PERSONAL OR AUTOMOTIVE SAFETY OR SECURITY DEVICES). INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. 40 DS513F1 |
Price & Availability of CS53L32A
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |