View PR31MA11NTZ_787896.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PR31MA11NTZ
PR31MA11NTZ
I Features
1. Low output current type. (Recommended RMS ON-state current:MAX 60mA) 2. Compact 5-pin dual-in-line package.
6-pin DIP Type SSR for Low Power Control
I Outline Dimensions
(Unit : mm)
Internal connection diagram
6 5 4 6 5 4
1. Electrical dampers for refrigerator. 2. Turntable controllers for microwave oven. 3. Ignitions circuit for oil fan heater.
6.50.3
I Applications
Anode mark
R31MA1
NC
1 2 3
0.60.2 1.20.3
1
2
3
I Absolute Maximum Ratings
Parameter Symbol Forward current IF Input VR Reverse voltage RMS ON-state current IT (rms) Output *1 Peak one cycle surge current Isurge Repetitive peak OFF-state voltage VDRM *2 Viso (rms) Isolation voltage Operating temperature Topr Storage temperature Tstg *3 Soldering temperature Tsol
*1 50Hz sine wave *2 AC for 1 minute, 40 to 60% RH, f=60Hz *3 For 10s
(Ta=25C) Rating Unit 50 mA 6 V mA 100 1.2 A 600 V V 5 000 -30 to +80 C -55 to +125 C 260 C
7.120.3
7.620.3
3.250.5 3.50.5
2.90.5
0.5TYP.
0.260.1 =0 to 13
0.5
0.1
2.540.25
1 2 3
Anode Cathode NC
4 6
Anode, Cathode Anode, Cathode
Pin
5
is not allowed external connection
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/
PR31MA11NTZ I Electro-optical Characteristics
Input Parameter Forward voltage Reverse current Repetitive peak OFF-state current ON-state voltage Holding current Critical rate of rise of OFF-state voltage Operating current (rms) Minimum trigger current Isolation resistance Turn-on time Symbol Conditions IF=20mA VF IR VR=3V IDRM VDRM=Rated VT IT=0.06A IH VD=6V - dV/dt VDRM=1/2 * Rated - AC200V, 60Hz, Resistance load IFT VD=6V, RL=100 RISO DC=500V, 40 to 60%RH VD=6V, RL=100, IF=20mA ton MIN. - - - - 0.1 500 - - 5x1010 - TYP. 1.2 - - - 1.0 - - - 1011 - MAX. 1.4 10-5 10-6 2.5 3.5 - 60 10 - 100 (Ta=25C) Unit V A A V mA V/s mA mA s
Output
Transfer characteristics
Fig.1 RMS ON-state Current vs. Ambient Temperature
120 100 80 60 40 20 0 -30
Fig.2 Forward Current vs. Ambient Temperature
60 50 Forward current IF (mA) 40 30 20 10 0 -30
RMS ON-state current IT (rms) (mA)
0
50
100
0
50
100
Ambient temperature Ta (C)
Ambient temperature Ta (C)
Fig.3 Operating Current vs. Ambient Temperature
70
60 Operating current (rms) (mA)
50
40
30
20 0 -30
0
50
100
Ambient temperature Ta (C)
NOTICE
q
The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: - - - Personal computers - -- Office automation equipment - -- Telecommunication equipment [terminal] - - - Test and measurement equipment - - - Industrial control - -- Audio visual equipment - -- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: - -- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - Traffic signals - - - Gas leakage sensor breakers - - - Alarm equipment - -- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - Space applications - -- Telecommunication equipment [trunk lines] - -- Nuclear power control equipment - -- Medical and other life support equipment (e.g., scuba).
q
q
q
Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
q
q
q

▲Up To Search▲

Price & Availability of PR31MA11NTZ

	To Download PR31MA11NTZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .