|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Advanced Analog Technology, Inc. AAT1110 Details are subject to change without notice ONE-CHANNEL STEP-DOWN PWM CONTROLLER Features Under-Voltage Lockout (UVLO) Protection Totem Pole Output Output Short Circuit Protection Incorporates Soft-Start Function Wide Operating FrequencyG 10 kHz to 1MHz Shutdown Control Low Dissipation Current : Typical 1.6mA in Operation SOP-8 & TSSOP-8 Package Available General Description The AAT1110 is a one-channel step-down PWM controller incorporating a soft-start function and a short circuit protection (SCP) function. Each device consists of an on-chip voltage reference, error amplifier, pulse width modulation controller, under-voltage protection, soft-start, and short circuit protection circuits. Switching frequencies up to 1MHz are set by an external resistor and capacitor. Soft-start time can be implemented by the SCP capacitor. Additionally, a chip enabled feature is provided to power down and reduce the supply current to 10 A . Pin Configuration With an optimized number of external components, the AAT1110 offers a simple and cost effective solution. VDD - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 1 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Pin Description Pin No 1 2 3 4 5 6 7 8 Name CE SCP VDD OUT GND OSC OE IE I/O I O O O I Description Chip Enable Input Pin] Internal Pull "H"^ Soft-Start and SCP Capacitor Connection Pin Power Supply Totem-Type Output Pin Ground Capacitor and Resistor Connection Pin for Setting the Oscillation Frequency Error Amplifier Output Pin Error Amplifier Inverting Input Pin Absolute Maximum Ratings Characteristics Supply Voltage Output Current Operating Free-Air Temperature Range Storage Temperature Range Power Dissipation Symbol VDD Value 7 - 120 /+120 - 20 to +85 - 45 to +125 Unit V IO TC Tstorage mA o o C C Pd 500 mW Recommended Operating Conditions Characteristics Supply Voltage, VDD Symbol VDD VI C OSC Min 2.6 0.5 Max 6.5 1.6 Unit V V Error Amplifier Input Voltage OSC Capacitor OSC Resistor Oscillator Frequency Output Current Operating Free-Air Temperature 100 1.0 10 - 20 10,000 10.0 1,000 +30/ - 30 +85 pF k R OSC f OSC IO TC kHz mA o C - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 2 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Electrical Characteristics, VDD = 3.3V (Unless Otherwise Specified) (See Note 1) Oscillator Parameter Test Condition C OSC = 270pF, R OSC = 4.2 k Min Typ Max Unit Oscillation Frequency Frequency Variation With Temperature Frequency Input Stability Under-Voltage Protection Parameter f OSC f T f V 400 500 5 600 kHz % % VDD = 2.6V to 6.5V 1 Upper Threshold Voltage Lower Threshold Voltage Hysteresis ( VUPH - VUPL ) VUPH VUPL VHYS Test Condition TC = 25 oC Min Typ Max Unit 2.12 2.47 1.96 2.28 0.19 2.85 2.63 V V V TC = 25 C TC = 25 C TC =25 oC o o Note1: Typical values of all parameters are specified at Short Circuit Protection Control Parameter Test Condition Min Typ Max Unit Input Threshold Voltage Short-Circuit Detect Threshold Voltage Charging Current Soft-Start Parameter Vr1 Vtscd I SCP VSCP =0V 1.160 1.262 1.360 1.160 1.262 1.360 - 2.15 V V - 1.50 - 1.00 A Charging Current Voltage at Soft-Start Completion Shutdown Control Parameter I CS Vts Test Condition VSCP =0V Min - 2.15 Typ Max Unit - 1.50 - 1.00 A 1.160 1.262 1.360 V Test Condition Min Typ Max Unit Shutdown Enable Voltage Shutdown Release Voltage VSE VSR 2.0 0.5 V V - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 3 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Electrical Characteristics, VDD = 3.3V (Unless Otherwise Specified) (See Note 1) EA (Error Amplifier) Parameter Input Threshold Voltage VT VTV VTT Test Condition VOE = 0.7V Min Typ Max Unit 1.249 1.262 1.275 1.4 2 1 0.1 1.7 0.05 20 - 75 V mV % A VT Input Stability VT Variation with Temperature Input Bias Current Output Voltage Swing Output Sink Current Output Source Current Open-Loop Voltage Gain Output Section Parameter VDD = 2.6 to 6.5V TC = - 20 oC to 90 oC 8 1.0 0.20 - IB VOS+ VOS- I OS+ I OS- A VO VOE =0.7V VOE =0.7V V mA A 3 - 45 70 85 dB High-Level Output Voltage Low-Level Output Voltage Rise Time Fall Time Operating Current Parameter VOH VOL t RISE t FALL Test Condition IO= - 30 mA Min Typ Max Unit 1.9 - 2.3 0.8 100 100 1.2 - V V ns ns IO=+30mA CL=1,000pF CL=1,000pF Supply Current I DD-OFF I DD-ON Test Condition Output "OFF" State Min Typ Max Unit - 1.3 1.6 - mA mA RT =4.2 k - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 4 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 How to Set the Time Constant for Soft-Start and Short Circuit Protection 1. Soft-Start At power on, the AAT1110 operates in soft-start mode. The capacitor C SCP connected to SCP pin starts charging at a constant current. In the soft-start mode, the voltage at SCP pin ( VSCP ) is input to the PWM comparator, so that the ON duty of the OUT pin is controlled by the VSCP . At completion of the soft-start operation, the voltage at the SCP pin stays low; the input from soft-start circuit to the PWM comparator stays high, and enters the short circuit protection waiting state. Soft-Start Time t s (sec) ~ 0.84 x C SCP (F) 2. Short Circuit Protection If the switching regulator output suddenly drops due to loading effect, the error amplifier output will be fixed at VOM + and capacitor C SCP will start charging. When the voltage at the SCP pin reaches approximately 1.26V, the output pin will set low and SCP pin will remain low. Once the protection circuit starts operating, the circuit can be recovered by setting the power supply. Short Circuit Detection Time t scp (sec) ~ 0.84 x C SCP (F) - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 5 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Block Diagram V DD CE C h ip E n a b le IREF GND V REF 1 .2 6 V SCP C om p. LA TCH SCP S o ft-S tart SCP UVC UVC CE OSC OSC CE UVLO V DD CE V REF 1 .2 6 v PW M Com p. V REF CE V DD OE V REF 1 .2 6 V E rr-A m p OUT UVC IE CE - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 6 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Application Circuit Buck (Step-Down) VDD Cscp VDD VDD VDD - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 7 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Buck (Step-Down) Timing Chart OE Reference Input for Short Circuit ldle Period Setting Voltage Soft-Start Setting Voltage OSC 1.262V Output SCP Soft-Start Output Short Circuit Output Short Circuit ts 2.47V Lockout Free VDD tscp - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 8 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Package Dimension 8-Pin SOP SYMBOLS A A1 A2 b C D E E1 e L y DIMENSIONS IN MILLIMETERS MIN 1.47 0.10 --0.33 0.19 4.80 5.80 3.80 --0.38 --0 TYP 1.60 --1.45 0.41 0.20 4.85 6.00 3.90 1.27 0.71 ----MAX 1.73 0.22 --0.51 0.25 4.95 6.20 4.00 --1.27 0.076 0 DEMINSIONS IN INCHES MIN 0.058 0.004 --0.013 0.0075 0.189 0.228 0.150 --0.015 --0 TYP 0.063 --0.057 0.016 0.008 0.191 0.236 0.154 0.050 0.028 ----MAX 0.068 0.008 --0.020 0.0098 0.195 0.244 0.157 --0.050 0 0 - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 9 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Tape and Reel 8-PinSOP - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 10 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Tape and Reel 8-Pin SOP (Cont.) NOTE: 1. 10 SPROCKET HOLE PITCH CUMULATIVE TOLERANCE 0.2 MILLIMETERS. 2. CAMBER NOT TO EXCEED 1 MILLIMETER IN 100 MILLIMETERS 3. MATERIAL: ANTI-STATIC BLACK ADVANTEK POLYSTYRENE. 4. A 0 AND B 0 ARE MEASURED ON A PLANE 0.3 MILLIMETERS ABOVE THE BOTTOM OF THE POCKET. 5. 6. K 0 IS MEASURED FROM A PLANE ON THE INSIDE BOTTOM OF THE POCKET TO THE TOP SURFACE OF THE CARRIER. POCKET POSITION RELATIVE TO SPROCKET HOLE IS MEASURED AS TRUE POSITION OF POCKET, NOT POCKET HOLE. - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 11 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Package Dimension TSSOP-8 - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 12 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Package Dimension TSSOP-8 SYMBOL A A1 A2 b C D E E1 e L y DIMENSION IN MILLIMETERS MIN TYP MAX 1.05 1.10 1.20 0.05 0.10 0.15 ----1.00 1.05 0.25 ----0.30 ----0.127 ----2.90 3.05 3.10 6.20 6.40 6.60 4.30 4.40 4.50 ----0.65 ----0.50 0.60 0.70 --------0.076 o o 0 8o 4 DIMENSION IN INCHES MIN TYP MAX 0.041 0.043 0.047 0.002 0.004 0.006 ----0.039 0.041 0.010 ----0.012 ----0.005 ----0.114 0.120 0.122 0.244 0.252 0.260 0.169 0.173 0.177 ----0.026 ----0.020 0.024 0.028 --------0.003 o o 0 8o 4 NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS. 2. LEAD FRAME MATERIAL: OLIN C7025/EFTEC 64T. 3. DIMENSION "D" DOES NOT INCLUDE MOLD FLASH, TIE BAR BURRS AND GATE BURRS. MOLD FLASH, TIE BAR BU 0.006" [0.15 MILLIMETERS] PER END. DIMENSION "E1" DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLA MILLIMETERS] PER SIDE. 4. DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.00 "b" DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS O PROTRUSION AND AN ADJACENT LEAD TO BE 0.0028" [0.07 MILLIMETERS]. 5. TOLERANCE: 0.010" [0.25 MILLIMETERES] UNLESS OTHERWISE SPECIFIED. 6. OTHERWISE DIMENSION FOLLOW ACCEPTABLE SPEC. 7. REFERENCE DOCUMENT: JEDEC SPEC MO-153. - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 13 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Tape and Reel TSSOP-8 - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 14 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Tape and Reel TSSOP-8 (Cont.) X.XXX X 0.0025 0.006 X.XXX 0.025 X.XX 0.10 X.X 0.25 X UNIT: MILLIMETERS NOTE: 1. 10 SPROCKET HOLE PITCH CUMULATIVE TOLERANCE 0.2 MILLIMETERS. 2. CHAMBER NOT TO EXCEED 1 MILLIMETER IN 100 MILLIMETERS. 3. MATERIAL: ANTI-STATIC BLACK ADVANTEK POLYSTYRENE. 4. A 0 AND B 0 ARE MEASURED ON A PLANE 0.3 MILLIMETERS ABOVE THE BOTTOM OF THE POCKET. 5. K 0 IS MEASURED FROM A PLANE ON THE INSIDE BOTTOM OF THE POCKET TO THE TOP SURFACE OF THE CARRIER. 6. POCKET POSITION RELATIVE TO SPROCKET HOLE IS MEASURED AS TRUE POSITION OF POCKET, NOT POCKET HOLE. - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 15 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Part Marking SOP8 Top Marking AAT1110 XXXXXX SOP8 Back Marking YYWW Part Marking TSSOP8 Top Marking AAT1110 XXXXXX TSSOP8 Back Marking YYWW - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 16 of 17 V 1.0 Advanced Analog Technology, Inc. AAT1110 Ordering Information - - xAEWAniN/|-1/2q - Advanced Analog Technology, Inc. - Page 17 of 17 V 1.0 |
Price & Availability of AAT1110-T2-T |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |