![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Preliminary data sheet TLE 5224 G2 Smart Two Channel Low-Side Switch Features * Power limitation * Overtemperature monitoring * Overload protection * Short circuit protection * Diagnostic feedback * Overvoltage protection * C compatible input * Electrostatic discharge (ESD) protection Product Summary Supply voltage Drain source voltage On resistance Output current Nom. output current VS VDS(AZ)max RON(typ) ID ID(ISO) 6.5 - 45 65 0.25 2x4 2 x 1.3 V V A A Application * All kinds of resistive and inductive loads (relays,electromagnetic valves) * C compatible power switch for 12 and 24 V applications * Solenoid control switch in automotive and industrial control systems P-DSO-24-3 General description Double channel Low-Side-Switch in Smart Power Technology (SPT) with two seperate inputs and two open drain DMOS output stages. The TLE 5224 G2 is fully protected by embedded protection functions and designed for automotive and industrial applications. Block Diagram VS Vbb Thermal overload TLE 5224 G2 Open Load Overload OUT1 Vbb Load 1 ENA IN1 ST1 LOGIC RPD Open Load Load 2 IN2 LOGIC Overload OUT2 ST2 RPD GND Semiconductor Group Page 1 03.02.97 Preliminary data sheet TLE 5224 G2 Block Diagram of Open Load Detection Semiconductor Group Page 2 03.02.97 Preliminary data sheet TLE 5224 G2 Maximum Ratings for Tj = - 40C to 150C Parameter Supply voltage Supply voltage operational range Continuous drain source voltage (OUT1, OUT2) Input voltage IN1, IN2, ENA Status output voltage Operating temperature range Storage temperature range Output current per channel Status output current Inductive load switch-off energy dissipation, single pulse Tj= 150C Thermal resistance Symbol VS VS VDS VIN VST Tj Tstg ID(lim) IST Values - 0.3 ... + 60 + 4.8 ... + 45 45 - 0.3 ... + 6 - 0.3 ... + 32 - 40 ... + 150 - 55 ... + 150 self limited - 5 ... + 5 400 12 75 K/W Unit V V V V V C A mA mJ 1 EAS junction - case RthJC junction - ambient RthJA Pin Definitions and Functions Pin Configuration(top view) Pin 1 2 3 4 5,6,7,8 9,10 11 12 13,14,15,16 17,18,19,20 21 22 23 24 Symbol IN1 ST2 OUT2 N.C. GND N.C. ENA VS N.C. GND N.C. OUT1 ST1 IN2 Function Control input channel 1 Status output channel 2 Power output channel 2 Not connected, cooling Ground, cooling Not connected, cooling Enable input for both channels Supply voltage Not connected, cooling Ground, cooling Not connected, cooling Power output channel 1 Status output channel 1 Control input channel 2 1 Case = Pin 5 to 8 and 17 to 20. Additionally the pins not connected (N.C.) have to be connected to the ground plane used as thermal heatsink to achieve the best thermal resistance. Page 3 03.02.97 Semiconductor Group Preliminary data sheet TLE 5224 G2 Electrical Characteristics Parameter and Conditions VS = 6.5 to 45 V ; T j = - 40 C to + 150 C (unless otherwise specified) 1. Power Supply (VS) Supply current (Outputs ON) Supply current (Output OFF) Operating voltage 2. Power Outputs ON state resistance; ID = 4A; VS 9.5 V Z-Diode clamping voltage (OUT1, OUT2) Pull down resistor Output on delay time 2 Output off delay time 2 Output on fall time 2 Output off rise time 2 Output off status delay time 2 Output on status delay time 2 3 4 Overload switch-off delay time 3 3. Digital Inputs (IN1, IN2, ENA) Input low voltage Input high voltage Input voltage hysteresis Input pull down current Enable pull down current VIN =5 V; VS 9 V VENA =5 V; VS 9 V Tj = 25 C Tj 125 C ID = 0.2 A ID = 2 A ID = 0.2 A ID = 2 A ID = 2 A Tj = 25 C Tj = 150C VS = 45 V VS 18 V VS 18 V Symbol Values min Unit typ max IS 2 5 4 2 45 mA mA V IS VS 1 4.8 RDS(ON) VDS(AZ) RPD ton toff tfall trise t4 t5 tDSO 45 14 10 10 0.25 0.5 65 20 25 50 20 25 40 26 40 40 V k s 20 50 60 50 150 VINL VINH VINHys IIN IENA - 0.3 2.0 0.2 50 15 100 30 1.0 6.0 0.6 140 45 V V V A A 4. Digital Status Outputs (ST1, ST2), open Drain Output voltage low Leakage current high IST = 2 mA VSTL ISTH 0.5 10 V A See timing diagram, resitive load condition; VS 9 V This parameter will not be tested but assured by design 4 Time till status valid after switching on or error detection 2 3 Semiconductor Group Page 4 03.02.97 Preliminary data sheet TLE 5224 G2 Electrical Characteristics Parameter and Conditions VS = 6.5 to 45 V ; T j = - 40 C to + 150 C (unless otherwise specified) 5. Diagnostic Functions Open load detection voltage (Output OFF) Open load compare voltage 5 Overload threshold current (VS 9.5 V) Overtemperature monitoring threshold Hysteresis 6 Symbol Values min Unit typ max VS 18 V VS = 12 V 18V > VDSC > 0.65*VS Tj = 25C Tj = 150C VDS(OL) VDS(OL)C ID(OL) ID(lim) Tth Thys 0.51*VS 6.2 VDSC-1.6 100 5.25 4 170 10 0.58*VS 7.0 VDSC-0.9 500 V V mA A Open load detection current (Output ON) 200 C K Application Description This IC is specially designed to drive inductive loads (relays, electromagnetic valves). Integrated clamp-diodes limit the output voltage peak when switching off an inductive load. For the detection of errors there are two status outputs, which monitor the following errors by logic levels: - thermal overload monitoring, - open and short load to ground in active an inactive mode, - overloading of output (also shorted load to supply) in active mode. Circuit Description Input Circuits The control and enable inputs, all active high, consist of Schmitt triggers with hysteresis. All inputs are connected with pull-down current sources. Not connected inputs are interpreted as "low". Switching Stages The power outputs consist of a DMOS power transistor with open drain. The output stages are shortload-protected throughout the operating range. Integrated clamp-diodes limit voltage spikes produced when inductive loads are discharged. Protective Circuit The outputs are protected against current overload. There is no protection against reverse polarity of the supply voltage. 5 6 VDSC is the output voltage of the other channel used for open load compare detection This parameter will not be tested but assured by design Page 5 03.02.97 Semiconductor Group Preliminary data sheet TLE 5224 G2 Error Detection The status output signal of the switching stages at normal operation is LOW = OFF; HIGH = ON. In case of any error the status outputs are set according to the table below. If current overload occurs, the error condition is stored in an internal register and the output is shutdown. To reset this register the control input of the affected channel has to be switched off and then on again. The state of the error detection circuit is directly dependent on the input status. In case of thermal overload the output stage will not be switched off but it will be monitored via the status outputs. Open load is detected for both on- and off-modus. In the on-modus the load current is monitored. If it drops below the specified threshold open load is detected. In the off mode, the ouput voltage is monitored. An open load condition is detected when the output voltage of a given channel is below 55 % of the supply voltage VS. Also the output voltages of two outputs are compaired against each other in off condition with a fixed offset of typ. 1.25 V to recognize GND bypasses. To suppress fault diagnosis during the flyback phase of the compared output, the diagnostic circuit includes a latch function. Reset of this latch is done at end of the flyback phase, additionally it can be reseted by a low signal on the enable input and by a high signal of the input signal. See also the block diagramm of open load detection. Diagnostic Table Operating Condition ENA L H H H H X L H X L H X L H L H H L H H Inputs IN1 X L H L H L X H L H H 1) X L H 1) IN2 X L L H H L X H 1) L H H 1) X L H Power Outputs Status Outputs OUT1 OFF OFF ON OFF ON OFF OFF ON OFF OFF ON 1) OFF OFF OFF 1) OUT2 OFF OFF OFF ON ON OFF OFF ON 1) OFF OFF ON 1) OFF OFF OFF ST1 L L H L H L L L H H L 1) L L L 1) ST2 L L L H H L L L 1) H H L 1) L L L Normal Function Thermal Overload Open Load Channel 1 Open Load Channel 2 Overload Channel 1 Overload Channel 2 1) see normal function Semiconductor Group Page 6 03.02.97 Preliminary data sheet TLE 5224 G2 Test Circuit V ST1 Application Circuit TLE The blocking capacitor C is recommended to avoid critical negative voltage spikes on VS in case of battery interruption during OFF-commutation. Semiconductor Group Page 7 03.02.97 Preliminary data sheet TLE 5224 G2 Timing Diagram VIN VI NH V INL t VDS VS 90% ton toff 10% t t fall t rise VST t5 t4 t Overload Current versus temperature 7 6,5 6 ID(lim) [ A ] 5,5 5 4,5 4 3,5 3 -50 -25 0 25 50 75 100 125 150 Junction Temperature [ C ] Semiconductor Group Page 8 03.02.97 Preliminary data sheet TLE 5224 G2 Package and ordering code all dimensions in mm P - DSO - 24 - L16 Ordering code Q67006-A9253 (Dual-in-line package, small-outline) 24 B 24 DIN 41870 T17 24 23 22 21 20 19 18 17 16 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 0.36 +0.13 1.27 0.76 max 15.4 -0.2 2.45 -0.2 0.1 min 7.6 -0.2 2.65 +0.07 max 0.25 10.3 0.3 Semiconductor Group Page 9 03.02.97 |
Price & Availability of TLE5224G2
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |