|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
19-2129; Rev 0; 8/01 Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN General Description The MAX4699/MAX4701/MAX4702 are low-voltage, single-supply CMOS analog switches. The MAX4699/ MAX4701 are dual double-pole/double-throw (DPDT) switches with two control inputs that control two single-pole/double-throw (SPDT) switches each. The MAX4702 is a quad SPDT switch with one control input and one low-voltage digital logic power supply. These devices operate from a single +1.8V to +5.5V power supply. When powered from a +2.7V supply the MAX4699/MAX4701/MAX4702 offer a 75 on-resistance (RON), with 12 max RON flatness and 4 max matching between channels. Each switch has Rail-toRail(R) signal handling, fast switching speeds of tON = 35ns, tOFF = 20ns, and a maximum 1nA of leakage current. The MAX4699/MAX4701 digital inputs are 1.8V-logic compatible when operated from a +3V supply. The MAX4702's digital inputs feature a 1.0V threshold when powered with a 1.5V logic supply. The MAX4699 is available in a space-saving 16-lead 4mm x 4mm QFN package. The MAX4701/MAX4702 are available in space-saving 16-lead 3mm x 3mm QFN and 16-pin TSSOP packages. Features o 3mm x 3mm and 4mm x 4mm 16-Pin QFN Package o Guaranteed On-Resistance: 75 (max) (+3V Supply) 40 (max) (+5V Supply) o Guaranteed Match Between Channels: 4 max o Guaranteed Flatness Over Signal Range: 12 max o Low Leakage Currents Over Temperature: 1nA Max at +85C o Fast Switching: tON = 35ns, tOFF = 20ns o Guaranteed Break-Before-Make o Single-Supply Operation from +1.8V to +5.5V o Rail-to-Rail Signal Handling o -3dB Bandwidth: 250MHz o Low Crosstalk: -79dB (1MHz) o High Off-Isolation: -76dB (1MHz) MAX4699/MAX4701/MAX4702 Applications Audio and Video Signal Routing Cellular Phones Battery-Operated Equipment Communications Circuits Modems PART MAX4699EGE MAX4701EUE MAX4701EGE MAX4702EUE MAX4702EGE Ordering Information TEMP. RANGE -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C PIN-PACKAGE 16 QFN (4mm x 4mm) 16 TSSOP 16 QFN (3mm x 3mm) 16 TSSOP 16 QFN (3mm x 3mm) Pin Configurations TOP VIEW COM1 16 NO1 15 V+ 14 NC4 13 COM1 16 NO1 15 V+ 14 NC4 13 NC1 1 12 COM4 NC1 1 12 COM4 IN1, IN2 *MAX4701/MAX4702 ARE IN A NO2 3mm x 3mm QFN PACKAGE COM2 2 MAX4699/ MAX4701* 11 NO4 IN 2 MAX4702* 11 NO4 3 10 1N3, IN4 NO2 COM2 3 10 VL 4 9 NC3 4 9 NC3 5 NC2 6 GND QFN 7 NO3 8 COM3 5 NC2 6 GND 7 NO3 QFN 8 COM3 Pin Configurations continued at end of data sheet. Rail-to-Rail is a registered trademark of Nippon Motorola, Inc. 1 ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN MAX4699/MAX4701/MAX4702 ABSOLUTE MAXIMUM RATINGS (Voltages Referenced to GND) V+ ............................................................................-0.3V to +6V VL, IN_, COM_, NO_, NC_ (Note1) .............. -0.3V to (V+ + 0.3V) Continuous Current COM_, NO_, NC_ ............................ 20mA Peak Current COM_, NO_, NC_ (pulsed at 1ms, 10% duty cycle)....................................................................40mA ESD per Method 3015.7....................................................>2.5kV Continuous Power Dissipation (TA = +70C) TSSOP (derate 5.6mW/C above +70C) ................. 444mW QFN (3 x 3) (derate 16.9mW/C above +70C) ...... 1349mW QFN (4 x 4) (derate 18.5mW/C above +70C) ...... 1481mW Operating Temperature Range .......................... -40C to +85C Storage Temperature Range ........................... -65C to +150C Lead Temperature (soldering, 10s) ............................... +300C Note 1: Signals on IN_, COM_, NO_, and NC_ exceeding 0 or V+ are clamped by internal diodes. Limit forward-diode current to maximum current rating. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS--Single +3V Supply (V+ = +2.7V to +3.3V, GND = 0, VIH = +1.4V, VIL = +0.5V, (VL = +1.5V, VIH = +1.0V, VIL = +0.4V for MAX4702 only), TA = -40C to +85C. Typical values are at V+ = +3V and TA = +25C, unless otherwise noted.) (Notes 2, 3) PARAMETER ANALOG SWITCH Analog Signal Range On-Resistance On-Resistance Match Between Channels (Note 4) On-Resistance Flatness (Note 5) NO_, NC_ Off-Leakage Current (Note 6) COM_ On-Leakage Current (Note 6) DYNAMIC Turn-On Time Turn-Off Time Break-Before-Make (Note 6) On-Channel -3dB Bandwidth Off-Isolation (Note 7) tON tOFF tBBM BW VISO VNO_ or VNC_ = +2V; RL = 300, CL = 35pF, Figure 2 VNO_ or VNC_ = +2V; RL = 300, CL = 35pF, Figure 2 VNO_ or VNC_ = +2V; RL = 300, CL = 35pF, Figure 2 Signal = 0, 50 in and out, Figure 5 f = 1MHz, RL = 50, CL = 5pF, Figure 5 +25C +25C TMIN to TMAX +25C TMIN to TMAX +25C TMIN to TMAX 1 250 -76 15 15 27 35 45 20 25 ns ns ns MHz dB VCOM_, VNO_, VNC_ RON RON V+ = +2.7V, ICOM_ = 10mA; VNO_ or VNC_ = +1.5V V+ = +2.7V, ICOM_ = 10mA; VNO_ or VNC_ = +1.5V V+ = +2.7V, ICOM_ = 10mA; VNO_ or VNC_ = +1V, +1.5V, +2V V+ = +3.3V, VCOM_ = +1V, +3V; VNO_ or VNC_ = +3V, +1V +25C TMIN to TMAX +25C TMIN to TMAX +25C TMIN to TMAX +25C TMIN to TMAX +25C TMIN to TMAX -0.5 -1 -0.5 -1 8 2 0 60 V+ 75 85 4 5 12 14 +0.5 1 +0.5 1 nA V nA SYMBOL CONDITIONS TA MIN TYP MAX UNITS RFLAT (ON) INO_(OFF), INC_(OFF) V+ = +3.3V, VCOM_ = +1V, ICOM_ (ON) +3V; VNO_ or VNC_ = +1V, +3V, or floating 2 _______________________________________________________________________________________ Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN ELECTRICAL CHARACTERISTICS--Single +3V Supply (continued) (V+ = +2.7V to +3.3V, GND = 0, VIH = +1.4V, VIL = +0.5V, (VL = +1.5V, VIH = +1.0V, VIL = +0.4V for MAX4702 only), TA = -40C to +85C. Typical values are at V+ = +3V and TA = +25C, unless otherwise noted.) (Notes 2, 3) PARAMETER Crosstalk (Note 8) Charge Injection NO_, NC_, Off-Capacitance Switch On-Capacitance Total Harmonic Distortion DIGITAL I/O Input Logic High Input Logic Low Input Leakage Current SUPPLY Power-Supply Range Logic Power-Supply Input Positive Supply Current V+ VL I+ V+ = +3.3V, VIN = 0 or V+ TMIN to TMAX 1.8 1.5 -1 5.5 V+ 1 V V A VIH VIL IIH, IIL MAX4699/MAX4701 MAX4702 (VL = +1.5V) MAX4699/MAX4701 MAX4702 (VL = +1.5V) VIN = 0 to V+ -1 1.4 1.0 0.8 0.4 1 V V A SYMBOL VCT Q CNO_(OFF), CNC_(OFF) C(ON) THD CONDITIONS f = 1MHz, RL = 50, CL = 5pF, Figure 5 VGEN = 0, RGEN = 0, CL = 1.0nF, Figure 4 f = 1MHz, VNO_, VNC_ = GND, Figure 6 f = 1MHz, Figure 6 f = 20Hz to 20kHz, 2.5Vp-p, RL = 600 TA +25C +25C +25C +25C +25C MIN TYP -79 0.5 8 20 0.02 MAX UNITS dB pC pF pF % MAX4699/MAX4701/MAX4702 ELECTRICAL CHARACTERISTICS--Single +5V Supply (V+ = +5V 10%, GND = 0, VIH = +2.4V, VIL = +0.8V, (VL = +1.5V, VIH = +1.0V, VIL = +0.4V for MAX4702 only), TA = -40C to +85C. Typical values are at V+ = +5V and TA = +25C, unless otherwise noted.) (Notes 2, 3) PARAMETER Analog Signal Range On-Resistance On-Resistance Match Between Channels (Note 4) On-Resistance Flatness (Note 5) DYNAMIC Turn-On Time tON VNO_ or VNC_ = +3V; RL = 300, CL = 35pF, Figure 2 +25C TMIN to TMAX 15 18 20 ns SYMBOL VCOM_, VNO_, VNC_ RON RON V+ = +4.5V, ICOM_ = 10mA; VNO_ or VNC_ = +3.5V V+ = +4.5V, ICOM_ = 10mA; VNO_ or VNC_ = +3.5V V+ = +4.5V, ICOM_ = 10mA; VNO_ or VNC_ = +2.0V, +2.25V, +3.5V +25C TMIN to TMAX +25C TMIN to TMAX +25C TMIN to TMAX 5 1 CONDITIONS TA MIN 0 30 TYP MAX V+ 40 50 3 5 8 10 UNITS V RFLAT (ON) _______________________________________________________________________________________ 3 Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN MAX4699/MAX4701/MAX4702 ELECTRICAL CHARACTERISTICS--Single +5V Supply (continued) (V+ = +5V 10%, GND = 0, VIH = +2.4V, VIL = +0.8V, (VL = +1.5V, VIH = +1.0V, VIL = +0.4V for MAX4702 only), TA = -40C to +85C. Typical values are at V+ = +5V and TA = +25C, unless otherwise noted.) (Notes 2, 3) PARAMETER Turn-Off Time Break-Before-Make (Note 6) Charge Injection DIGITAL I/O Input Logic High Input Logic Low Logic Input Current VIH VIL IIH, IIL MAX4699/MAX4701 MAX4702 (VL = +1.5V) MAX4699/MAX4701 MAX4702 (VL = +1.5V) VIN = 0 to V+ -1 2.4 1.0 0.8 0.4 1 V V A SYMBOL tOFF tBBM Q CONDITIONS VNO_ or VNC_ = +3V; RL = 300, CL = 35pF, Figure 2 VNO_ or VNC_ = +3V; RL = 300, CL = 35pF, Figure 2 VGEN = 0, RGEN = 0, CL = 1.0nF, Figure 4 TA +25C TMIN to TMAX +25C TMIN to TMAX +25C 2 0.5 10 MIN TYP 7 MAX 12 15 UNITS ns ns pC Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: -40C specifications are guaranteed by design. Note 4: RON = RON(MAX) - RON(MIN). Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal ranges. Note 6: Guaranteed by design. Note 7: Off-Isolation = 20log10 (VCOM_ / VNO), VCOM = output, VNO = input to off switch. Note 8: Between any two switches. 4 _______________________________________________________________________________________ Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN Typical Operating Characteristics (TA = +25C, unless otherwise noted. VL = +1.5V for MAX4702 only) ON-RESISTANCE vs. COM VOLTAGE OVER SUPPLY VOLTAGE 120 110 100 90 80 70 60 50 40 30 20 10 0 0 MAX4699 toc01 MAX4699/MAX4701/MAX4702 ON-RESISTANCE vs. COM VOLTAGE OVER TEMPERATURE (V+ = +2.7V) MAX4699 toc02 ON-RESISTANCE vs. COM VOLTAGE OVER TEMPERATURE (V+ = +3.3V) TA = +25C 50 40 RON () 30 20 10 0 TA = -40C TA = +85C MAX4699 toc03 80 70 60 TA = +25C TA = +85C 60 V+ = +1.8V RON () V+ = +2.7V V+ = +3.3V RON () 50 40 30 20 TA = -40C ICOM = 10mA 1 2 V+ = +5V 3 4 5 10 0 0 V+ = +2.7V ICOM = 10mA 0.5 1.0 1.5 VCOM (V) 2.0 2.5 V+ = +3.3V ICOM = 10mA 0 0.5 1.0 1.5 2.0 2.5 3.0 VCOM (V) VCOM (V) ON-RESISTANCE vs. COM VOLTAGE OVER TEMPERATURE (V+ = +5V) MAX4699 toc04 ON-LEAKAGE CURRENT vs. TEMPERATURE MAX4699 toc05a OFF-LEAKAGE CURRENT vs. TEMPERATURE MAX4699 toc05b 40 TA = +25C 30 RON () TA = +85C 1000 1000 20 SUPPLY CURRENT (pA) 100 OFF-LEAKAGE CURRENT (pA) 100 10 10 10 V+ = +5V ICOM = 10mA 0 0 1 2 TA = -40C 1 V+ = +2.7V 0.1 1 V+ = +2.7V 0.1 -40 -20 0 20 40 60 80 3 4 5 -40 -20 0 20 40 60 80 VCOM (V) TEMPERATURE (C) TEMPERATURE (C) CHARGE INJECTION vs. COM VOLTAGE OVER SUPPLY VOLTAGE MAX4699 toc06 SUPPLY CURRENT vs. TEMPERATURE MAX4699 toc07 SUPPLY CURRENT vs. LOGIC INPUT VOLTAGE MAX4701 100 SUPPLY CURRENT (A) 10 1 0.1 0.01 0.001 V+ = +2.7V MAX4699 toc08 5 ICOM = 10mA CHARGE INJECTION (pC) 4 1000 100 SUPPLY CURRENT (nA) 10 1 0.1 0.01 1000 3 V+ = +5V 2 V+ = +3V 1 0.0001 0.00001 0 0 1 2 3 4 5 VCOM (V) 0.001 -40 -20 0 20 40 60 80 TEMPERATURE (C) 0.000001 0 0.5 1.0 1.5 2.0 2.5 LOGIC INPUT VOLTAGE (V) _______________________________________________________________________________________ 5 Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN MAX4699/MAX4701/MAX4702 Typical Operating Characteristics (continued) (TA = +25C, unless otherwise noted. VL = +1.5V for MAX4702 only) TURN-ON/OFF TIME vs. SUPPLY VOLTAGE MAX4699 toc09 TURN-ON/OFF TIME vs. TEMPERATURE MAX4699 toc10 LOGIC THRESHOLD vs. VL MAX4702 VIN RISING LOGIC THRESHOLD (V) 1.2 1.0 VIN FALLING 0.8 0.6 0.4 0.2 0 V+ = +5V 1.4 MAX4699 toc11 30 25 20 tON 15 10 5 0 2.7 3.2 3.7 4.2 4.7 5.2 SUPPLY VOLTAGE (V) 40 V+ = +2.7V 35 30 tON/tOFF (ns) 25 20 15 10 5 -40 -20 0 20 40 60 80 TEMPERATURE (C) tOFF tON 1.6 tON/tOFF (ns) tOFF 1 2 3 VL (V) 4 5 FREQUENCY RESPONSE ON-REPONSE MAX4699 toc12 TOTAL HARMONIC DISTORTION vs. FREQUENCY MAX4699 toc13 0 -20 -40 LOSS (dB) 0.1 THD (%) OFF-ISOLATION -60 -80 -100 -120 0.1 1 10 FREQUENCY (MHz) 100 1000 CROSSTALK 0.01 RL = 600 0.001 10 100 1k FREQUENCY (Hz) 10k 100k 6 _______________________________________________________________________________________ Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN Pin Description QFN PIN MAX4699/ MAX4701 1 -- 2 3 4 5 6 7 8 9 -- 10 11 12 13 14 15 16 MAX4702 1 2 -- 3 4 5 6 7 8 9 10 -- 11 12 13 14 15 16 TSSOP PIN MAX4701 3 -- 4 5 6 7 8 9 10 11 -- 12 13 14 15 16 1 2 MAX4702 3 4 -- 5 6 7 8 9 10 11 12 -- 13 14 15 16 1 2 NAME NC1 IN IN1, IN2 NO2 COM2 NC2 GND NO3 COM3 NC3 VL IN3, IN4 NO4 COM4 NC4 V+ NO1 COM1 FUNCTION Analog Switch 1--Normally Closed Terminal Digital Control Input Switch 1, 2, 3, and 4 Digital Control Input Switch 1 and 2 Analog Switch 2--Normally Open Terminal Analog Switch 2--Common Terminal Analog Switch 2--Normally Closed Terminal Ground Analog Switch 3--Normally Open Terminal Analog Switch 3--Common Terminal Analog Switch 3--Normally Closed Terminal Logic Power-Supply Input Digital Control Input Switch 3 and 4 Analog Switch 4--Normally Open Terminal Analog Switch 4--Common Terminal Analog Switch 4--Normally Closed Terminal Positive Supply Voltage Input Analog Switch 1--Normally Open Terminal Analog Switch 1--Common Terminal POSITIVE SUPPLY D1 V+ MAX4699/MAX4701/MAX4702 Detailed Description The MAX4699/MAX4701 are low-voltage CMOS analog switches that operate from a single +1.8V to +5.5V power supply. The MAX4702 requires an additional logic supply that allows for setting lower logic thresholds. The MAX4699/MAX4701 are double-pole/doublethrow (DPDT) devices. The MAX4702 is a quad single-pole/double-throw (SPDT) device. These devices feature a break-before-make switching, fast switching speeds (with V+ = 5V: tON = 18ns max, tOFF = 9ns max and with V+ = 3V: tON = 35ns, tOFF = 20) and rail-to-rail signal handling. A logic input on the MAX4702 allows for logic thresholds as low as 1.0V. MAX4699 MAX4701 MAX4702 NO Vg COM GND D2 Applications Information Analog Signal Levels Analog signals that range over the entire supply voltage (V+ to GND) can be passed with very little change in onresistance (see Typical Operating Characteristics). The switches are bidirectional, so the NO, NC, and COM pins can be used as either inputs or outputs. Figure 1. Overvoltage Protection Using Two External Blocking Diodes _______________________________________________________________________________________ 7 Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN MAX4699/MAX4701/MAX4702 Power-Supply Sequencing and Overvoltage Protection Caution: Do not exceed the absolute maximum ratings because stresses beyond the listed ratings may cause permanent damage to the devices. Proper power-supply sequencing is recommended for all CMOS devices. Always apply V+ before applying analog signals, especially if the analog signal is not current limited. If this sequencing is not possible, and if the analog inputs are not current limited to <20mA, add a small-signal diode (D1) as shown in Figure 1. If the analog signal can dip below GND, add D2. Adding protection diodes reduces the analog range to a diode drop (about 0.7V) below V+ (for D1), and a diode drop above ground (for D2). On-resistance increases slightly at low supply voltages. Maximum supply voltage (V+) must not exceed +6V. Adding protection diode D2 causes the logic threshold to be shifted relative to GND. TTL compatibility is not guaranteed when D2 is added. Protection diodes D1 and D2 also protect against some overvoltage situations. With Figure 1's circuit, if the supply voltage is below the absolute maximum rating, and if a fault voltage up to the absolute maximum rating is applied to an analog signal pin, no damage will result. VL Logic Input (MAX4702) The MAX4702 features a VL logic input that allows for lower logic input thresholds down to 1.0V min for VIH in the quad SPDT configuration. Power-up VL after V+ has been powered with a minimum of 1.5V to ensure proper operation of the device. Test Circuits/Timing Diagrams MAX4699 MAX4701 MAX4702 VN_ NO_ OR NC_ V+ V+ COM_ RL 300 IN_ LOGIC INPUT GND SWITCH OUTPUT 0 t ON LOGIC INPUT VOUT CL 35pF VOUT 0.9 x V0UT t OFF 0.9 x VOUT VIH 50% VIL t r < 5ns t f < 5ns VOUT = VN_ CL INCLUDES FIXTURE AND STRAY CAPACITANCE. RL RL + RON ( ) LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE THE OPPOSITE LOGIC SENSE. Figure 2. Switching Time MAX4699 MAX4701 MAX4702 VN_ NC_ NO_ IN_ LOGIC INPUT GND V+ V+ COM_ RL 300 VOUT CL 35pF LOGIC INPUT VIH 50% VIL VOUT tD CL INCLUDES FIXTURE AND STRAY CAPACITANCE. 0.9 x VOUT Figure 3. Break-Before-Make Interval 8 _______________________________________________________________________________________ Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN Test Circuits/Timing Diagrams (continued) V+ MAX4699/MAX4701/MAX4702 MAX4699 MAX4701 MAX4702 VOUT VOUT VOUT CL IN_ OFF ON OFF V+ RGEN NC_ OR NO_ GND IN COM_ V GEN VIL TO VIH IN_ OFF ON Q = (V OUT )(C L ) OFF IN DEPENDS ON SWITCH CONFIGURATION; INPUT POLARITY DETERMINED BY SENSE OF SWITCH. Figure 4. Charge Injection V+ 10nF NETWORK ANALYZER V OR V+ IN_ V+ COM_ VIN 50 50 V OFF-ISOLATION = 20log OUT VIN V ON-LOSS = 20log OUT VIN V CROSSTALK = 20log OUT VIN NC_ 50 MAX4699 MAX4701 MAX4702 GND NO_ VOUT MEAS REF 50 50 MEASUREMENTS ARE STANDARDIZED AGAINST SHORTS AT IC TERMINALS. OFF-ISOLATION IS MEASURED BETWEEN COM_ AND "OFF" NO_ OR NC_ TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM_ AND "ON" NO_ OR NC_TERMINAL ON EACH SWITCH. CROSSTALK IS MEASURED FROM ONE CHANNEL TO ALL OTHER CHANNELS. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 5. On-Loss, Off-Isolation, and Crosstalk 10nF V+ Chip Information TRANSISTOR COUNT: 269 Substrate connected to GND MAX4699 MAX4701 MAX4702 IN_ V+ COM_ CAPACITANCE METER f = 1MHz NC_ or NO_ GND VIL OR VIH Figure 6. Channel Off/On-Capacitance _______________________________________________________________________________________ 9 Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN MAX4699/MAX4701/MAX4702 Pin Configurations (continued) TOP VIEW MAX4701 MAX4702 NO1 1 COM1 2 NC1 3 IN1, IN2 4 NO2 5 COM2 6 NC2 7 GND 8 16 V+ 15 NC4 14 COM4 13 NO4 12 1N3, IN4 11 NC3 10 COM3 9 NO3 SWITCHES SHOWN FOR LOGIC "0" INPUTS NO1 1 COM1 2 NC1 3 IN 4 NO2 5 COM2 6 NC2 7 GND 8 16 V+ 15 NC4 14 COM4 13 NO4 12 VL 11 NC3 10 COM3 9 NO3 TSSOP IN1, IN2 L H -- -- IN3, IN4 -- -- L H ON SWITCHES NC1-COM1, NC2-COM2 NO1-COM1, NO2-COM2 NC3-COM3, NC4-COM4 NO3-COM3, NO4-COM4 TSSOP IN L H ON SWITCHES NC1-COM1, NC2-COM2 NC3-COM3, NC4-COM4 NO1-COM1, NO2-COM2 NO3-COM3, NO4-COM4 10 ______________________________________________________________________________________ Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN Package Information 32L QFN, 3x3x0.85.EPS MAX4699/MAX4701/MAX4702 ______________________________________________________________________________________ 11 Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN MAX4699/MAX4701/MAX4702 Package Information (continued) 12, 16,20, 24L QFN.EPS 12 ______________________________________________________________________________________ Low-Voltage, Dual DPDT/Quad SPDT Analog Switches in QFN Package Information (continued) MAX4699/MAX4701/MAX4702 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 (c) 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. |
Price & Availability of MAX4702 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |